kth.sePublikationer
Ändra sökning
Länk till posten
Permanent länk

Direktlänk
Publikationer (8 of 8) Visa alla publikationer
Ribca, I., Sochor, B., Roth, S. V., Lawoko, M., Meier, M. A. .. & Johansson, M. (2023). Effect of Molecular Organization on the Properties of Fractionated Lignin-Based Thiol-Ene Thermoset Materials. ACS Omega, 8(28), 25478-25486
Öppna denna publikation i ny flik eller fönster >>Effect of Molecular Organization on the Properties of Fractionated Lignin-Based Thiol-Ene Thermoset Materials
Visa övriga...
2023 (Engelska)Ingår i: ACS Omega, E-ISSN 2470-1343, Vol. 8, nr 28, s. 25478-25486Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

In this study, the combination of sequential solvent fractionation of technical Kraft lignin was followed by allylation of most OH functionalities to give highly functional thermoset resins. All lignin fractions were highly functionalized on the phenolic (≥95%) and carboxylic acid OH (≥85%) and to a significant extent on the aliphatic OH moieties (between 43 and 75%). The resins were subsequently cross-linked using thiol-ene chemistry. The high amount of allyl functionalities resulted in a high cross-link density. Dynamic mechanical analysis measurements showed that the thioether content, directly related to the allyl content, strongly affects the performance of these thermosets with a glass transition temperature (Tg) between 81 and 95 °C and with a storage modulus between 1.9 and 3.8 GPa for all thermosets. The lignin fractions and lignin-based thermosets’ morphology, at the nanoscale, was studied by wide-angle X-ray scattering measurements. Two π-π stacking interactions were observed: sandwich (≈4.1-4.7 Å) and T-shaped (≈5.5-7.2 Å). The introduction of allyl functionalities weakens the T-shaped π-π stacking interactions. A new signal corresponding to a distance of ≈3.5 Å was observed in lignin-based thermosets, which was attributed to a thioether organized structure. At the same time, a lignin superstructure was observed with a distance/size corresponding to 7.9-17.5 Å in all samples.

Ort, förlag, år, upplaga, sidor
American Chemical Society (ACS), 2023
Nationell ämneskategori
Polymerkemi
Identifikatorer
urn:nbn:se:kth:diva-349575 (URN)10.1021/acsomega.3c03022 (DOI)001021456700001 ()2-s2.0-85164912868 (Scopus ID)
Anmärkning

QC 20240702

Tillgänglig från: 2024-07-02 Skapad: 2024-07-02 Senast uppdaterad: 2024-07-02Bibliografiskt granskad
Ribca, I., Sochor, B., Betker, M., Roth, S. V., Lawoko, M., Sevastyanova, O., . . . Johansson, M. (2023). Impact of lignin source on the performance of thermoset resins. European Polymer Journal, 194, 112141-112141, Article ID 112141.
Öppna denna publikation i ny flik eller fönster >>Impact of lignin source on the performance of thermoset resins
Visa övriga...
2023 (Engelska)Ingår i: European Polymer Journal, ISSN 0014-3057, E-ISSN 1873-1945, Vol. 194, s. 112141-112141, artikel-id 112141Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

A series of different technical hardwood lignin-based resins have been successfully synthesized, characterized, and utilised to produce thiol-ene thermoset polymers. Firstly, technical lignin was fractionated and allylated, whereafter it was crosslinked with a trifunctional thiol. Structural and morphological characteristics of the lignin fractions were studied by 1H NMR, 31P NMR, SEC, FTIR, DSC, TGA, and WAXS. The hardwood lignin fractions have a high content of C5-substituted OH groups. The WAXS studies on lignin fractions revealed the presence of two π-π stacking conformations, sandwiched (4.08–4.25 Å) and T-shaped (6.52–6.91 Å). The presence of lignin superstructures with distances/sizes between 10.5 and 12.8 Å was also identified. The curing reaction of the thermosets was investigated by RT-FTIR. Almost all thermosets (excepting one fraction) reached 95% of the thiol conversion in less than 17 h, revealing the enhanced reactivity of the allylated hardwood lignin samples.

The mechanical properties of the thermosets were investigated by DMA. The curing performance, as well as the final thermoset properties, have been correlated to variations in chemical composition and morphological differences of lignin fractions. The described results clearly demonstrate that technical hardwood lignins can be utilized for these applications, but also that significant differences compared to softwood lignins have to be considered for material design.

Ort, förlag, år, upplaga, sidor
Elsevier BV, 2023
Nyckelord
Hardwood lignin, Solvent fractionation, Allylation, Thiol-ene thermosets, Wide-angle X-ray scattering, π-π stacking interactions
Nationell ämneskategori
Materialkemi Polymerteknologi Polymerkemi Pappers-, massa- och fiberteknik
Forskningsämne
Kemi
Identifikatorer
urn:nbn:se:kth:diva-327220 (URN)10.1016/j.eurpolymj.2023.112141 (DOI)001000190100001 ()2-s2.0-85159278832 (Scopus ID)
Forskningsfinansiär
KTH
Anmärkning

QC 20230524

Tillgänglig från: 2023-05-22 Skapad: 2023-05-22 Senast uppdaterad: 2023-06-26Bibliografiskt granskad
Ribca, I. (2023). Lignin-Based Thermosets with Tunable Mechanical and Morphological Properties: A Study of Structure-Property Relationships. (Doctoral dissertation). Stockholm, Sweden: KTH Royal Institute of Technology
Öppna denna publikation i ny flik eller fönster >>Lignin-Based Thermosets with Tunable Mechanical and Morphological Properties: A Study of Structure-Property Relationships
2023 (Engelska)Doktorsavhandling, sammanläggning (Övrigt vetenskapligt)
Abstract [en]

Nowadays, there is an urgent need to decrease our dependence on fossilresources and shift towards the use of renewable resources for advancingsustainable development. Utilizing renewable and bio-based raw materials,such as lignocellulosic biomass, for designing new materials is a promisingapproach to promote this objective. The main components of lignocellulosicbiomass are cellulose, hemicellulose, and lignin. Lignin is the most abundantaromatic biopolymer in nature and it is produced on a large scale fromchemical pulping processes as technical lignin. Lignin has the potential as asustainable and renewable alternative to fossil-based aromatics in variousapplications, e.g. thermosetting resins.

Technical lignin has a complex and heterogeneous structure, with arelatively low chemical reactivity. It is characterized by a high dispersity, thepresence of various functional groups that are unevenly distributed along thelignin chains, and various interunit linkages between the monoaromatics. Toovercome the challenges associated with lignin heterogeneity, technicallignin can be fractionated and/or chemically modified.

In this work, LignoBoost Kraft lignin was used as a starting material toproduce lignin-based thiol-ene thermosets. Firstly, lignin was fractionatedusing two approaches: 1) sequential solvent fractionation, and 2) microwaveassistedextraction. These fractionation approaches enabled access to ligninfractions with unique and tunable properties. Subsequently, lignin waschemically modified, in particular through allylation. Two allylation reagentswere used: allyl chloride and diallyl carbonate. The use of allyl chlorideenables a selective allylation of the phenolic OH groups, leaving the aliphaticand carboxylic acid OH groups unmodified. On the other hand, diallylcarbonate can react with all the aforementioned OH groups, leading to ahigher degree of allylation. Subsequently, allylated lignin was thermallycross-linked with various polyfunctional thiols, leading to thiol-enethermosets. The structure-property relationships of the thermosets wereinvestigated by varying several parameters, including the lignin source,fractionation approach, chemical modification, and thiol cross-linker. Byadjusting these parameters, various thermosets with tunable mechanical andmorphological properties were produced. Understanding the structurepropertyrelationships of these bio-based materials is crucial for identifyingpotential applications.

Abstract [sv]

Nuförtiden finns det ett akut behov av att minska vårt beroende av fossilaresurser och övergå till användningen av förnybara resurser och därmedavancera den hållbara utvecklingen. Att använda förnybara och biobaseraderåvaror, såsom lignocellulosabiomassa, för att designa nya material är ettlovande tillvägagångssätt för att uppnå detta mål. Huvudkomponenterna ilignocellulosabiomassa är cellulosa, hemicellulosa och lignin. Lignin ärnaturens vanligaste aromatiska biopolymer och den produceras i stor skalafrån kemiska massaprocesser som tekniskt lignin. Lignin kan fungera som etthållbart och förnybart alternativ till fossilbaserade aromater i olikatillämpningar, t.ex. g. värmehärdande hartser.

Tekniskt lignin har en komplex och heterogen struktur, med en relativt lågkemisk reaktivitet. Det kännetecknas av en hög dispersitet, närvaron av olikafunktionella grupper som är ojämnt fördelade längs ligninkedjorna, och olikatyper av enhetsbindningar mellan monoaromaterna. För att övervinna deutmaningar som är förknippade med ligninets heterogenitet kan ligninfraktioneras och/eller kemiskt modifieras.

I detta arbete användes LignoBoost Kraft-lignin som utgångsmaterial föratt tillverka ligninbaserade tiol-en-härdplaster. Först har lignin fraktioneratsmed hjälp av två olika metoder: 1) sekventiell lösningsmedelsfraktionering,och 2) mikrovågsassisterad extraktion. Dessa fraktioneringsmetoder gjordedet möjligt att erhålla ligninfraktioner med unika och skräddarsyddaegenskaper. Därefter modifierades ligninet kemiskt genom allylering. Tvåallyleringsreagens användes: allylklorid och diallylkarbonat. Användningenav allylklorid möjliggör selektiv allylering av de fenoliska OH-grupperna,samtidigt som de alifatiska och karboxylsyra-OH-grupperna lämnasomodifierade. Diallylkarbonat kan å andra sidan reagera med alla de tidigarenämnda OH-grupperna, vilket leder till en högre grad av allylering. Däreftertvärbands härdades allylerat lignin termiskt med olika polyfunktionellatioler, för att ge härdplast med tiol-en-tvärbindingar. Strukturegenskapsförhållandenaför härdplasterna undersöktes genom att varieraflera parametrar, inklusive ligninkällan, fraktioneringsmetod, kemiskmodifiering och tioltvärbindare. Genom att justera dessa parametrarproducerades olika härdplaster med skräddarsydda mekaniska ochmorfologiska egenskaper. Att förstå relationerna mellan struktur ochegenskaper av dessa biobaserade material är avgörande för att identifierapotentiella tillämpningar.

Ort, förlag, år, upplaga, sidor
Stockholm, Sweden: KTH Royal Institute of Technology, 2023. s. 66
Serie
TRITA-CBH-FOU ; 2023:19
Nyckelord
Softwood, hardwood, technical lignin, solvent fractionation, allylation, thiol-ene thermosets, thioether linkage, wide-angle X-ray scattering, π-π stacking interactions, Barrträ, lövträ, tekniskt lignin, lösningsmedelsfraktionering, allylering, tiol-en-härdplaster, tioeterbindning, vidvinkelröntgenspridning, π-π staplingsinteraktioner
Nationell ämneskategori
Organisk kemi Polymerkemi Polymerteknologi Materialkemi
Forskningsämne
Fiber- och polymervetenskap
Identifikatorer
urn:nbn:se:kth:diva-327306 (URN)978-91-8040-567-6 (ISBN)
Disputation
2023-06-15, F3, Lindstedtsvägen 26 & 28, Stockholm, 10:00 (Engelska)
Opponent
Handledare
Forskningsfinansiär
Knut och Alice Wallenbergs Stiftelse
Anmärkning

QC 2023-05-23

Tillgänglig från: 2023-05-23 Skapad: 2023-05-23 Senast uppdaterad: 2023-05-25Bibliografiskt granskad
Truncali, A., Ribca, I., Yao, J. G., Hakkarainen, M. & Johansson, M. (2023). Microwave-assisted fractionation and functionalization of technical lignin toward thermoset resins. Journal of Applied Polymer Science, 140(45), Article ID e54645.
Öppna denna publikation i ny flik eller fönster >>Microwave-assisted fractionation and functionalization of technical lignin toward thermoset resins
Visa övriga...
2023 (Engelska)Ingår i: Journal of Applied Polymer Science, ISSN 0021-8995, E-ISSN 1097-4628, Vol. 140, nr 45, artikel-id e54645Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

Lignin is the most abundant aromatic biopolymer, with a potential to serve as a building block of rigid and thermally stable bio-based materials. However, it is still underutilized because of the heterogeneous and not fully understood chemical structure. Here, technical softwood Kraft lignin is refined in to narrow-dispersity and relatively low molar mass fractions by microwave-assisted processing, followed by microwave-assisted allylation and further application in lignin-based thermosets. This microwave processing is carried out under non-catalyzed conditions using a low boiling point solvent and elevated pressure. The properties of the retrieved fractions are investigated by 31P-NMR, heteronuclear single quantum coherence spectroscopy-NMR, SEC, differential scanning calorimetry, and thermogravimetric analysis. The extraction yield of the selected lignin fraction is around 25%, with the number-average molar mass (Mn), weight-average molar mass (Mw), and dispersity (Đ) significantly reduced. The chemically modified lignin is characterized by 31P NMR and FTIR, which provides evidence of the introduction of the allyl moieties. The analyses demonstrate that 90 ± 3% of the hydroxyl groups in fractionated lignin are successfully allylated. Subsequently, the allylated lignin is cross-linked through thermally induced thiol-ene chemistry to produce lignin-based thermosets. The final thermosets exhibit a storage modulus of 4050 ± 60 MPa and a Tg of 105 ± 5°C.

Ort, förlag, år, upplaga, sidor
Wiley, 2023
Nyckelord
allylation, microwave-assisted fractionation, microwave-assisted functionalization, softwood lignin, thiol-ene thermosets
Nationell ämneskategori
Polymerkemi
Identifikatorer
urn:nbn:se:kth:diva-347512 (URN)10.1002/app.54645 (DOI)001060855200001 ()2-s2.0-85169677590 (Scopus ID)
Anmärkning

QC 20240617

Tillgänglig från: 2024-06-17 Skapad: 2024-06-17 Senast uppdaterad: 2024-06-17Bibliografiskt granskad
Wolfs, J., Ribca, I., Meier, M. A. .. & Johansson, M. (2023). Polythionourethane Thermoset Synthesis via Activation of Elemental Sulfur in an Efficient Multicomponent Reaction Approach. ACS Sustainable Chemistry and Engineering, 11(9), 3952-3962
Öppna denna publikation i ny flik eller fönster >>Polythionourethane Thermoset Synthesis via Activation of Elemental Sulfur in an Efficient Multicomponent Reaction Approach
2023 (Engelska)Ingår i: ACS Sustainable Chemistry and Engineering, E-ISSN 2168-0485, Vol. 11, nr 9, s. 3952-3962Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

For the transition toward a safer and more sustainable production of polymeric materials, new synthetic concepts need to be developed. Herein, we describe a catalytic, solvent-free synthesis approach for novel thionourethane thermoset materials, in which the diisothiocyanate reactant is generated in situ via a sulfurization of isocyanides with elemental sulfur, preventing the exposure and handling of the diisothiocyanate. In this one-pot procedure, castor oil fulfills a dual role: (i) acting as the solvent for the in situ diisothiocyanate synthesis in the first step and (ii) reacting as the polyol component in the subsequent thionourethane thermoset formation. The kinetics of the consecutive two steps were studied in detail via real-time IR measurements, and the thermoset crosslinking step was found to be thermally triggerable after the diisothiocyanate reactant is quantitatively formed, enabling high control over the curing process of the system. Differential scanning calorimetry, thermogravimetric analysis, and rheological measurements were performed to investigate the thermal and mechanical properties of the novel thionourethane thermosets and then compared to analogous polyurethane materials. Our results demonstrate an unprecedented approach for thermoset synthesis via an in situ reagent synthesis, i.e., the generation of isothiocyanates from isocyanides by catalytic activation of elemental sulfur, and subsequent thermally triggerable thermosetting with a polyol, resulting in materials with appealing properties.

Ort, förlag, år, upplaga, sidor
American Chemical Society, 2023
Nyckelord
castor oil, DBU, isocyanide, isothiocyanate, multicomponent reaction, organocatalysis, sulfur, thermoset, thiourethane
Nationell ämneskategori
Polymerkemi Organisk kemi
Identifikatorer
urn:nbn:se:kth:diva-330957 (URN)10.1021/acssuschemeng.3c00143 (DOI)000935519600001 ()2-s2.0-85148872086 (Scopus ID)
Anmärkning

QC 20230707

Tillgänglig från: 2023-07-07 Skapad: 2023-07-07 Senast uppdaterad: 2023-07-07Bibliografiskt granskad
Ribca, I., Jawerth, M., Brett, C., Lawoko, M., Schwartzkopf, M., Chumakov, A., . . . Johansson, M. (2021). Exploring the Effects of Different Cross-Linkers on Lignin-Based Thermoset Properties and Morphologies. ACS Sustainable Chemistry and Engineering, 9(4), 1692-1702
Öppna denna publikation i ny flik eller fönster >>Exploring the Effects of Different Cross-Linkers on Lignin-Based Thermoset Properties and Morphologies
Visa övriga...
2021 (Engelska)Ingår i: ACS Sustainable Chemistry and Engineering, E-ISSN 2168-0485, Vol. 9, nr 4, s. 1692-1702Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

The search for sustainable material solutions has put lignin as one of the prime candidates for aromatic building blocks in macromolecular materials. The present study aimed to demonstrate how lignin-based thermoset resins can be utilized in combination with different cross-linkers. Kraft lignin was used to produce thermosets with tunable mechanical and morphological properties. The lignin-based thermosets were obtained via a thermally induced thiol–ene reaction. The first part of this work was focused on Kraft lignin solvent fractionation and chemical modification of the ethanol soluble fraction. Chemical analysis indicated that the allylation process was selective toward phenolic hydroxyl groups. SAXS and SEM studies demonstrated that solvent fractionation and allylation processes affected the molecular and nanoscale morphological characteristics of lignin. The second part’s focus was on how the properties of thermosets can be tuned by using three different cross-linkers. The dynamic mechanical and morphological properties of three different thermosets were investigated via DMA, SAXS, and WAXS techniques. The three different thermosets exhibit similar molecular morphology but different storage modulus and glass transition temperature. In this work, it was shown that despite lignin’s heterogeneity it was possible to produce thermosetting materials with tunable properties.

Nyckelord
Kraft lignin, Solvent fractionation, Selective allylation, Thiol−ene thermoset, Mechanical properties, Small- and wide-angle X-ray scattering
Nationell ämneskategori
Pappers-, massa- och fiberteknik Polymerkemi
Forskningsämne
Kemi
Identifikatorer
urn:nbn:se:kth:diva-289222 (URN)10.1021/acssuschemeng.0c07580 (DOI)000617925200026 ()2-s2.0-85099956480 (Scopus ID)
Forskningsfinansiär
Knut och Alice Wallenbergs Stiftelse, CGFB 63343
Anmärkning

QC 20210217

Tillgänglig från: 2021-01-22 Skapad: 2021-01-22 Senast uppdaterad: 2024-03-18Bibliografiskt granskad
Ribca, I., Sochor, B., Roth, S. V., Lawoko, M., Meier, M. A. R. & Johansson, M.Effect of Molecular Organization on the Properties of Fractionated Lignin-Based Thiol-Ene Thermoset Materials.
Öppna denna publikation i ny flik eller fönster >>Effect of Molecular Organization on the Properties of Fractionated Lignin-Based Thiol-Ene Thermoset Materials
Visa övriga...
(Engelska)Manuskript (preprint) (Övrigt vetenskapligt)
Abstract [en]

In this study, the combination of sequential solvent fractionation of technical Kraft lignin were followed by allylation of most OH functionalities to give highly functional thermoset resins. All lignin fractions were highly functionalized on the phenolic (≥95%) and carboxylic acid OH (≥85%), and to a significant extent on the aliphatic OH moieties (between 43 and 75%). The resins were subsequently cross-linked using thiol-ene chemistry. The high amount of allyl functionalities resulted in a high cross-link density. DMA measurements showed that thioether content dominates the performance of these thermosets with a glass transition temperature (Tg) between 73 and 99 °C and with a storage modulus between 1.9 and 3.8 GPa for all thermosets. The lignin fractions and lignin-based thermosets morphology, at nanoscale, was studied by wide angle X-ray scattering measurements (WAXS). Two π-π stacking interactions were observed: sandwich (≈4.1–4.7 Å) and T-shaped (≈5.5–7.2 Å). The introduction of allyl functionalities weakens the T-shaped π-π stacking interactions. A new signal corresponding to a distance of ≈3.5 Å was observed in lignin-based thermosets, which was attributed to a thioether organized structure. At the same time, a lignin superstructure, was observed with a distance/size corresponding to 7.9-17.5 Å in all samples.

Nyckelord
Softwood lignin, solvent fractionation, allylation, thiol-ene thermosets, thioether linkage, wide-angle X-ray scattering, π-π stacking interaction, superstructures
Nationell ämneskategori
Organisk kemi Polymerkemi Polymerteknologi Pappers-, massa- och fiberteknik
Forskningsämne
Kemi
Identifikatorer
urn:nbn:se:kth:diva-327224 (URN)
Forskningsfinansiär
Knut och Alice Wallenbergs Stiftelse
Anmärkning

QC 20230524

Tillgänglig från: 2023-05-22 Skapad: 2023-05-22 Senast uppdaterad: 2023-05-24Bibliografiskt granskad
Truncali, A., Ribca, I., Yao, J. G., Hakkarainen, M. & Johansson, M.Microwave-Assisted Fractionation and Functionalization of Technical Lignin Towards Thermoset Resins.
Öppna denna publikation i ny flik eller fönster >>Microwave-Assisted Fractionation and Functionalization of Technical Lignin Towards Thermoset Resins
Visa övriga...
(Engelska)Manuskript (preprint) (Övrigt vetenskapligt)
Abstract [en]

Lignin is the main source of aromatic natural polymers, with a potential to serve as a building block of rigid and thermally stable bio-based materials. However, because of its heterogeneity differences and not fully understood chemical structure it is still underutilized. Therefore, in this paper, technical softwood Kraft lignin is refined in to narrow-dispersity and relatively low molecular weight fractions by microwave-assisted processing. This process was carried out under non-catalytic conditions using a low boiling point solvent and higher pressure. The chemical properties of the retrieved fractions were investigated by 31P NMR, HSQC NMR, SEC, DSC, and TGA. One of the retrieved soluble lignin fractions was successfully chemically modified by microwave processing. The chemically modified lignin was characterized by 31P NMR and FTIR, which provided evidence of the introduction of the allyl moieties. Subsequently, the allylated lignin was cross-linked through thermally induced thiol-ene chemistry to produce lignin-based thermosets.

Nyckelord
Softwood lignin, microwave-assisted fractionation, microwave-assisted functionalization, allylation, thiol-ene thermosets.
Nationell ämneskategori
Polymerkemi Polymerteknologi Pappers-, massa- och fiberteknik
Forskningsämne
Kemi
Identifikatorer
urn:nbn:se:kth:diva-327223 (URN)
Forskningsfinansiär
Knut och Alice Wallenbergs Stiftelse
Anmärkning

QC 20230524

Tillgänglig från: 2023-05-22 Skapad: 2023-05-22 Senast uppdaterad: 2024-05-23Bibliografiskt granskad
Organisationer
Identifikatorer
ORCID-id: ORCID iD iconorcid.org/0000-0002-8127-9183

Sök vidare i DiVA

Visa alla publikationer