This work describes the enhanced mechanical properties of the composite nanofibers and the photodegradation of two organic dyes using PAN/CNTs under UV irradiation at different volume concentration (0.05, 0.1, 0.2, and 0.3 wt.%). The composite nanofibers was performed with polyacrylonitrile (PAN), and carbon nanotubes (CNTs) by electrospinning process. The composite nanofibers structure and morphology is characterized by XRD, FTIR, SEM, and TEM. The result indicates that with increasing CNTs content, the mechanical properties of the composite nanofibers was enhanced, and became more elastic, and the elastic modulus increased drastically. The results of mechanical properties exhibit improvements in tensile strengths, and elastic modulus by 38% and 84% respectively, at only 0.05 wt.% CNTs. Moreover, photocatalytic degradation performance in short time and low power intensity was achieved comparison to earlier reports.

A novel material composite nanofibers (PAN-CNT/TiO2-NH2) based on adsorption of Cr(VI) ions, was applied. Polyacrylonitrile (PAN) and carbon nanotube (CNTs)/titanium dioxide nanoparticles (TiO2) functionalized with amine groups (TiO2-NH2) composite nanofibers have been fabricated by electrospinning. The nanostructures and the formation process mechanism of the obtained PAN-CNT/TiO2-NH2 composite nanofibers are investigated using FTIR, XRD, XPS, SEM, and TEM. The composite nanofibers were used as a novel adsorbent for removing toxic chromium Cr(VI) in aqueous solution. The kinetic study, adsorption isotherm, pH effect, initial concentration, and thermodynamic study were investigated in batch experiments. The composite nanofibers had a positive effect on the absorption of Cr(VI) ions under neutral and acidic conditions, and the saturated adsorption reached the highest when pH was 2. The adsorption equilibrium reached within 30 and 180 min with an initial solution concentration increasing from 10 to 300 mg/L, and the process can be better described using nonlinear pseudo first than nonlinear pseudo second order model and Intra-particle diffusion. Isotherm data fitted well using linear and nonlinear Langmuir, Freundlich, Redlich-Peterson, and Temkin isotherm adsorption model. Thermodynamic study showed that the adsorption process is exothermic. The adsorption capacity can remain up to 80% after 5 times usage, which show good durability performance. The adsorption mechanism was also studied by UV-vis and XPS.

In this study highly efficient photocatalyst based on composite nanofibers containing polyacrylonitrile (PAN), carbon nanotubes (CNT), and surface functionalized TiO2 nanoparticles was developed. The composite nanofibers were fabricated using electrospinning technique followed by chemical crosslinking. The surface modification and morphology changes of the fabricated composite nanofibers were examined through SEM, TEM, and FTIR analysis. The photocatalytic performance of the composite nanofibers for the degradation of model molecules, methylene blue and indigo carmine, under UV irradiation in aqueous solutions was investigated. The results demonstrated that high photodegradation efficiency was obtained in a short time and at low power intensity compared to other reported studies. The effective factors on the degradation of the dyes, such as the amount of catalyst, solution pH and irradiation time were investigated. The experimental kinetic data were fitted using pseudo-first order model. The effect of the composite nanofibers as individual components on the degradation efficiency of MB and IC was evaluated in order to understand the overall photodegradation mechanism. The results obtained showed that all the components possess significant effect on the photodegradation activity of the composite nanofibers. The stability studies demonstrated that the photodegradation efficiency can remain constant at the level of 99% after five consecutive cycles.

In this work we report a highly efficient photocatalytic reduction of Cr(VI) based on PAN-CNT/TiO2-NH2 composite nanofibers fabricated by using electrospinning technique followed by chemical crosslinking of surface modified TiO2 NPs functionalized with amino group. The structure and morphology of the fabricated composite nanofibers were characterized by FTIR, SEM, TEM, TGA, and XPS. The results indicate that the composite nanofibers possess excellent photoreduction performance for Cr(VI) under visible light (125 W) after 30 min, which is much faster than previous reports. The effects of various experimental parameters such as catalyst dose, irradiation time, initial concentration of Cr(VI), and pH on the photoreduction efficiency of Cr(VI) were investigated. The highest photoreduction efficiency of Cr (VI) was obtained at low acidity and low amount of TiO2/CNT photocatalyst. The kinetic experimental data was attained and fitted well with a pseudo-first-order model. The UV–vis spectrophotometer and XPS analyses proved that chromate Cr(VI) was reduced to Cr(III). In addition, it can be concluded that the addition of the phenol enhances the photocatalytic reduction of Cr(VI). Furthermore, the photoreduction mechanism has also been discussed. Finally, the fabricated composite nanofibers were found to be stable after at least five regeneration cycles.