Accelerometertillbehör till mobiltelefon: - Utveckling av Blåtands ansluten accelerometermodul till smartphone
2008 (svensk)Independent thesis Advanced level (degree of Master (Two Years)), 20 poäng / 30 hp
OppgaveAlternativ tittel
Accelerometer accessory to a mobile phone : - Development of Blutooth connected accelerometer to a smartphone (engelsk)
Abstract [en]
This master thesis has been carried out as a prototype development project. The project has
been performed in cooperation with ÅF Combra AB. The purpose with the master thesis is to
construct a Bluetooth interface between an accelerometer and a smartphone and constructing
a physical prototype containing an accelerometer. This is done to test a new user interface to
mobile phones. The master thesis has also included a research about the possibility to
implement distance measuring with Bluetooth. Combra has in the past worked with both
Bluetooth and smartphones, but never in the same application.
One part of the master thesis was to construct a working physical prototype. This resulted in
that the master thesis has a predominantly practical characteristic. Special focus has been
placed on the construction phase. The logic has been programmed on both sides of the
Bluetooth interface. This means in both the accelerometer module and in the smartphone.
The prototype is built around a microprocessor and has apart from the accelerometer and the
Bluetooth link, two push buttons and two light diodes. The majority of the signal management
is located in the phone. The system is constructed in that way to simplify further
developments later on. Focus was placed on getting the accelerometer module as energy
efficient as possible.
The conclusion of the project is that it is possible to construct a lot of different applications
and user interfaces to the developed system. Application software is only needed to be added
to the phone in further developments. Distance measuring with Bluetooth is possible but a
compromise between accuracy, energy efficiency and stability has to be made.
Abstract [sv]
Examensarbetet har genomförts som ett prototyputvecklingsprojekt. Projektet har utförts i
samarbete med ÅF Combra AB. Syftet med examensarbetet är att konstruera ett
Blåtandsgränssnitt mellan en accelerometer och en smartphone och konstruera en fysisk
prototyp innehållande accelerometern. Detta för att kunna experimentera med ett nytt
användarinterface till mobiltelefoner. Examensarbetet har även innefattat en undersökning av
hur en avståndsbedömning skulle kunna genomföras med Blåtand. Combra har tidigare
arbetat med både Blåtand och smartphones men aldrig i samma tillämpning.
Då det ingick i examensarbetet att konstruera en fungerande fysisk prototyp, har detta medfört
att examensarbete varit av övervägande praktisk karaktär. Speciellt fokus har lagts på
konstruktionsfasen. Logik har programmerats på båda sidorna av Blåtandsgränssnittet. Det
innebär såväl till den egenhändigt konstruerade accelerometermodulen som till smartphonen.
Prototypen är uppbyggd kring en mikroprocessor och har förutom en accelerometer och en
Blåtandslänk även två tryckknappar och två lysdioder. Majoriteten av signalbehandlingen
ligger i telefonen. Systemet konstruerades på detta sätt för att lätt kunna bygga ut
funktionalitet i ett senare skede. Fokus lades dessutom på att få accelerometermodulen så
energisnål som möjligt.
Slutsatsen av projektet är att det är möjligt att konstruera en mängd olika applikationer och
användargränssnitt till det konstruerade systemet. Mjukvara behöver enbart läggas till på
telefonsidan vid vidareutveckling. Avståndsbedömning med blåtand är möjligt, dock måste en
kompromiss göras mellan noggrannhet, energiförbrukning och robusthet.
sted, utgiver, år, opplag, sider
2008.
Serie
MMK 2008:70 MDA315
HSV kategori
Identifikatorer
URN: urn:nbn:se:kth:diva-100705OAI: oai:DiVA.org:kth-100705DiVA, id: diva2:544556
Eksternt samarbeid
ÅF Combra AB,Lennart Persson
Uppsök
Technology
Veileder
Examiner
2012-08-152012-08-152022-06-24bibliografisk kontrollert