Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Machining of CoCr28Mo6
KTH, Skolan för industriell teknik och management (ITM), Materialvetenskap, Materialens processteknologi.
2011 (engelsk)Independent thesis Advanced level (degree of Master (Two Years)), 20 poäng / 30 hpOppgave
Abstract [en]

The machining process of Cobait-Chromium medical ailoys become a veryessential topic for research due to widening range of application. They aregeneraily used because of their high wear resistance, low corrosioncharacteristics and high fatigue strength. This project describes an investigationof chip formation during the machining of Cobalt-Chromium-Molybdenum highcarbon alloy. A quick stop device has been employed to investigate mechanismof chip formation through analyzing of shear zone and shear plane. Thicknessmeasurement of segments, surface conditions after finishing, lowest valley andhighest peak with three different cutting tool inserts were studied as weil.Moreover cutting force measurement at different cutting speeds, feeds and radialnoses were performed. Microstructure and hardness of work material before andafter machining has been studied. Tool life of inserts was evaluated bymeasuring flank wear.

The consequences obtained from the study illuminated:

  1. For the constant cutting speed and nose radius flank wear increased whenthe feed increased.
  2. For the constant feed and nose radius, increase in the cutting speedlowered flank and crater wear.
  3. Cutting force increased with the increase in feed.
  4. Increase in cutting speed to 40 m/min raised cutting force. However afterthat cutting force decreased.
  5. Insert CNMG 120408-MF1 TS2000 with cutting data v~=70 m/min, ap= 3mm and f=0.1 mm seemed fit the best in base of lower flank and craterwear, almost lower cutting force and smoother finish roughness.
sted, utgiver, år, opplag, sider
2011. , s. 74
Emneord [en]
Turning, Transition Metal Alloys, Orthopedic Medical Devices, Chip Formation, Co28Cr6Mo, Inserts, Flank Wear, Loads, Surface Properties
HSV kategori
Identifikatorer
URN: urn:nbn:se:kth:diva-108172OAI: oai:DiVA.org:kth-108172DiVA, id: diva2:579174
Eksternt samarbeid
Sandvik Materials Technology
Presentation
2011-03-29, N111, BV23,KTH, Stockholm, 14:41 (engelsk)
Uppsök
Technology
Veileder
Examiner
Tilgjengelig fra: 2013-01-07 Laget: 2012-12-19 Sist oppdatert: 2013-01-07bibliografisk kontrollert

Open Access i DiVA

Fulltekst mangler i DiVA

Søk i DiVA

Av forfatter/redaktør
Alipour, Yousef
Av organisasjonen

Søk utenfor DiVA

GoogleGoogle Scholar

urn-nbn

Altmetric

urn-nbn
Totalt: 501 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf