Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Rail wear development: measurements and evaluation
KTH, Tidigare Institutioner                               , Maskinkonstruktion.
2002 (engelsk)Rapport (Annet vitenskapelig)
sted, utgiver, år, opplag, sider
Stockholm: KTH , 2002. , s. 52
Serie
Trita-FKT ; 2002:22
HSV kategori
Identifikatorer
URN: urn:nbn:se:kth:diva-4914OAI: oai:DiVA.org:kth-4914DiVA, id: diva2:7013
Merknad
QC 20101015Tilgjengelig fra: 2005-02-09 Laget: 2005-02-09 Sist oppdatert: 2010-10-15bibliografisk kontrollert
Inngår i avhandling
1. On wear in rolling/sliding contacts
Åpne denne publikasjonen i ny fane eller vindu >>On wear in rolling/sliding contacts
2005 (engelsk)Doktoravhandling, med artikler (Annet vitenskapelig)
Abstract [en]

The aim of this thesis is to increase the understanding of wear in rolling/sliding contacts such as the wheel-rail contact for railroads and the roller-washer contact for roller bearings.

The Stockholm commuter train network has been the subject of papers A and B in this thesis in which the wear and surface cracks on rails has been observed for a period of three years. By comparing the wear depth with the crack length, equilibrium between these two damage mechanisms was found for a lubricated rail. By using a lubricant with friction modifiers the stresses was low enough to prevent crack propagation; at the same time, the rail was hard enough to reduce the wear rate. This is probably the most favourable state in terms of rail maintenance cost.

Roller bearings subjected to lubricant borne particles have been the subject of papers C, D and E in this thesis. Particles in the lubricating oil can have a significant impact on the wear in lubricated contacts. Even at low concentration levels can self-generated particles cause significant wear. The here presented results shows that filtration during run-in can significantly reduce both the mass loss and the number of self generated particles. A series of experiments has been carried out to study the wear of roller bearings by ingested lubricant borne hard particles. The form of the worn profile and the length of wear scratches correspond closely to the sliding within the contact. A count of the number of wear scratches on the rolling element surface indicates that the contact concentrates particles. A novel wear model based on the observation of a single point on the contacting surface when a concentration of particles passes through it has been developed and the necessary data for the model has been determined from the experiments. Comparison of the simulation results with the experimental results shows good qualitative agreement for the form change of the washer surfaces.

sted, utgiver, år, opplag, sider
Stockholm: KTH, 2005. s. x, 20
Serie
Trita-MMK, ISSN 1400-1179 ; 2005:03
Emneord
Technology, wear, rolling, sliding, contact, environment, TEKNIKVETENSKAP
HSV kategori
Identifikatorer
urn:nbn:se:kth:diva-122 (URN)
Disputas
2005-02-11, Kollegiesalen, Valhallavägen 79, Stockholm, 09:30
Opponent
Veileder
Merknad
QC 20101015Tilgjengelig fra: 2005-02-09 Laget: 2005-02-09 Sist oppdatert: 2012-01-27bibliografisk kontrollert

Open Access i DiVA

Fulltekst mangler i DiVA

Søk i DiVA

Av forfatter/redaktør
Nilsson, Rickard
Av organisasjonen

Søk utenfor DiVA

GoogleGoogle Scholar

urn-nbn

Altmetric

urn-nbn
Totalt: 543 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf