Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
The influence of edge geometry on end-correction coefficients in micro perforated plates
Eindhoven University of Technology, Department of Mechanical Engineering, Dynamics and Control, The Netherlands.
Eindhoven University of Technology, Department of Mechanical Engineering, Dynamics and Control, The Netherlands.
KTH, Skolan för teknikvetenskap (SCI), Farkost och flyg. KTH, Skolan för teknikvetenskap (SCI), Centra, VinnExcellence Center for ECO2 Vehicle design.ORCID-id: 0000-0002-9061-4174
KTH, Skolan för teknikvetenskap (SCI), Centra, Linné Flow Center, FLOW. KTH, Skolan för teknikvetenskap (SCI), Farkost och flyg, MWL Marcus Wallenberg Laboratoriet.ORCID-id: 0000-0001-7898-8643
Vise andre og tillknytning
2015 (engelsk)Inngår i: Journal of the Acoustical Society of America, ISSN 0001-4966, E-ISSN 1520-8524, Vol. 138, nr 6, s. 3668-3677Artikkel i tidsskrift (Fagfellevurdert) Published
Resurstyp
Text
Abstract [en]

Global expressions are proposed for end-correction coefficients in micro perforated plates (MPPs) using non-dimensional parameters. MPPs are sound absorbers with small perforation diameters such that the Stokes boundary layers fill up almost the entire perforation. Sound absorption does not only occur within the perforation, but also takes place just outside of it. The latter contribution plus the outside inertia effect on the transfer impedance of the MPP are referred to as end-corrections. In order to determine them, an analytical solution employing the very thin Stokes layer assumption has been derived. However, this assumption requires empirical coefficients in the end-corrections for accurate results. To explore the effects of various parameters a numerical model is used. This model is verified with open-end reflection coefficient measurements. The most prominent result from this study is that compared to plate thickness, the ratio of perforation diameter to Stokes layer thickness (Shear number) and edge geometry affect the end-correction coefficients more significantly. The effect of plate thickness can be neglected for practical purposes, therefore, expressions for the end-corrections in terms of Shear number and edge geometry are provided. The relative error of these expressions is <3% compared to the numerical results. 

sted, utgiver, år, opplag, sider
American Institute of Physics (AIP), 2015. Vol. 138, nr 6, s. 3668-3677
Emneord [en]
MICROPERFORATED MATERIALS, DUCT, FLOW
HSV kategori
Identifikatorer
URN: urn:nbn:se:kth:diva-181392DOI: 10.1121/1.4937748ISI: 000367535700034PubMedID: 26723322Scopus ID: 2-s2.0-84950979050OAI: oai:DiVA.org:kth-181392DiVA, id: diva2:899424
Merknad

QC 20160201

Tilgjengelig fra: 2016-02-01 Laget: 2016-02-01 Sist oppdatert: 2017-11-30bibliografisk kontrollert

Open Access i DiVA

Fulltekst mangler i DiVA

Andre lenker

Forlagets fulltekstPubMedScopus

Personposter BETA

Efraimsson, GunillaÅbom, Mats

Søk i DiVA

Av forfatter/redaktør
Efraimsson, GunillaÅbom, Mats
Av organisasjonen
I samme tidsskrift
Journal of the Acoustical Society of America

Søk utenfor DiVA

GoogleGoogle Scholar

doi
pubmed
urn-nbn

Altmetric

doi
pubmed
urn-nbn
Totalt: 479 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf