Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
On Simulation of Uniform Wear and Profile Evolution in the Wheel - Rail Contact
KTH, Skolan för teknikvetenskap (SCI), Farkost och flyg, Järnvägsteknik.ORCID-id: 0000-0002-3447-6686
2006 (Engelska)Doktorsavhandling, sammanläggning (Övrigt vetenskapligt)
Abstract [en]

Numerical procedures for reliable wheel and rail wear prediction are rare. Recent development of simulation techniques and computer power together with tribological knowledge do however suggest computer aided wear prediction as possible. The present objective is to devise a numerical procedure able to simulate profile evolution due to uniform wear sufficiently accurate for application to vehicle dynamics simulation. Such a tool should be useful for maintenance planning, optimisation of the railway system and its components as well as trouble-shooting. More specifically, the field of application may include estimation of reprofiling frequency, optimisation of wheel – rail profile match, optimisation of running gear suspension parameters, and recognition of unfavourable profile evolution influencing the dynamic response of the vehicle.

The research contribution accounted for in this thesis includes, besides a literature review, modelling of the wheel – rail interface, benchmarking against traditional methods, and validation with respect to full-scale measurements.

The first part addresses wheel – rail contact conditions in the context of wear simulation as well as tribological environment and tractive forces. The current approach includes Archard’s wear model with associated wear maps, vehicle dynamics simulation, and railway network definition. One objective is to be able to include variations in operation conditions in the set of simulations instead of using scaling factors. In particular the influence of disc braking and varying lubrication conditions have been investigated. Both environmental factors like moist and contamination and deliberate lubrication need to be considered. As part of the associated contact analysis the influence of tangential elastic deformation of the contacting surfaces has been investigated and found to be essential in case of partial slip contact conditions. The influence on the calculated wear of replacing the Hertzian contact by a non-elliptic semi-Hertzian method has been investigated, showing relocation of material loss towards increased profile curvature.

In the second part comparisons have been carried out with traditional methods, where the material loss is assumed to be directly related to the energy dissipated in the contact. Attention has been paid to the understanding of the principle differences between the investigated methods, comparing the distribution of friction energy, sliding velocity, and wear depth. As a prerequisite, contact conditions with dependence on wheelset guidance and curving performance as well as influence of tractive forces have been investigated.

In the final part validation of the developments related to wheel wear simulation is addressed. Disc braking has been included and a wear map for moist contact conditions based on recent tests has been drafted. Good agreement with measurements from the reference operation, is achieved. Further a procedure for simulation of rail wear and corresponding profile evolution has been formulated. A simulation set is selected defining the vehicles running on the track to be investigated, their operating conditions, and contact parameters. Trial calculations of a few curves show qualitatively good results in terms of profile shape development and difference in wear mechanisms between gauge corner and rail head. The wear rates related to traffic tonnage are however overestimated. The impact of the model improvements accounted for in the first part of the thesis has been investigated, indicating directions for further development.

Ort, förlag, år, upplaga, sidor
Stockholm: KTH , 2006. , s. x, 100
Serie
Trita-AVE, ISSN 1651-7660 ; 2006:83
Nyckelord [en]
wheel-rail contact, wear, wear prediction, wear model, wheel profile, rail
Nationell ämneskategori
Farkostteknik
Identifikatorer
URN: urn:nbn:se:kth:diva-4184ISBN: 978-91-7178-605-3 (tryckt)OAI: oai:DiVA.org:kth-4184DiVA, id: diva2:11125
Disputation
2006-12-05, Salongen, KTHB, Osquars Backe 31, Stockholm, 10:00
Opponent
Handledare
Anmärkning
QC 20110124Tillgänglig från: 2006-11-22 Skapad: 2006-11-22 Senast uppdaterad: 2011-11-24Bibliografiskt granskad
Delarbeten
1. Simulation of railway wheel profile development due to wear: influence of disc braking and contact environment
Öppna denna publikation i ny flik eller fönster >>Simulation of railway wheel profile development due to wear: influence of disc braking and contact environment
2005 (Engelska)Ingår i: Wear, ISSN 0043-1648, E-ISSN 1873-2577, Vol. 258, nr 7-8, s. 1055-1063Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

This paper addresses issues related to braking and wheel-rail contact conditions in the context of wheel wear simulation. The KTH approach to the topic includes Archard's wear model with associated wear maps, vehicle dynamics simulation and railway network definition. In previous work at KTH certain variations in operating conditions have been accounted for through empirically estimated average scaling factors. The objective of the current research is to be able to include such variations in the set of simulations. In particular the influence of disc braking as well as varying friction and lubrication conditions are investigated. Both environmental factors like moist and contamination and deliberate lubrication need to be considered. As part of the associated contact analysis the influence of local elastic deformation on the sliding velocity has been separately investigated.

Ort, förlag, år, upplaga, sidor
Elsevier, 2005
Nyckelord
railway wheel wear, wheel profile, simulation, disc braking
Nationell ämneskategori
Farkostteknik
Forskningsämne
Järnvägsgruppen - Fordonsteknik
Identifikatorer
urn:nbn:se:kth:diva-6415 (URN)10.1016/j.wear.2004.03.055 (DOI)000227273800013 ()2-s2.0-13844269270 (Scopus ID)
Anmärkning

QC 20100531. 6th International Conference on Contact Mechanics and Wear of Rail/Wheel Systems. GOTHENBURG, SWEDEN. JUN 10-13, 2003

Tillgänglig från: 2006-11-22 Skapad: 2006-11-22 Senast uppdaterad: 2017-12-14Bibliografiskt granskad
2. Impact of non-elliptic contact modelling in wheel wear simulation
Öppna denna publikation i ny flik eller fönster >>Impact of non-elliptic contact modelling in wheel wear simulation
2008 (Engelska)Ingår i: Wear, ISSN 0043-1648, E-ISSN 1873-2577, Vol. 265, nr 9-10, s. 1532-1541Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

Advances in simulation of railway wheel wear in the sense of material removal have drawn the attention to the importance of wheel–rail contact modelling. As a further step of enhancing the used simulation procedure in direction of increased generality and reduced need for application-dependent calibration, the focus of this investigation is the influence of non-elliptic contact models on the wheel wear rate and profile shape. To facilitate evaluation the semi-Hertzian contact procedure Stripes, developed by INRETS in France, has been implemented.

To investigate the capabilities of Stripes to assess the contact area and pressure, shape comparisons have been made with other numerical methods for a set of wheel–rail contact situations. The referenced results are based on the linear elastic half-space assumption, elastic finite element analysis, and elastic–plastic finite element analysis. For reference also the elliptic contact area according to Hertz is shown as given by the contact data table of the multi-body simulation code.

After exploring the properties of the Stripes procedure with respect to contact area estimation and pressure distribution, the focus is moved to the influence on wear rate, being the principal objective of this investigation. First the wear distribution over the contact patch is studied and compared to results using the elliptic model from the MBS code Gensys and the non-elliptic approach with Kalker's code Contact. Finally the evolution of the wheel profile is simulated for a few typical cases.

This investigation of wear distributions over non-elliptic patches under different operating conditions indicates significant differences compared to both Contact and the applied Hertzian approach. The expansion from single contact occasions to complete simulations indicates comparable material removal rates but relocation towards the flange side. This tendency is apparent in all of the cases shown, however limited to initial wear in tangent run or reasonably mild curve negotiation.

Nyckelord
Wheel–rail contact, Non-elliptic contact, Railway wheel wear, Wheel profile, Simulation
Nationell ämneskategori
Farkostteknik
Forskningsämne
Järnvägsgruppen - Fordonsteknik
Identifikatorer
urn:nbn:se:kth:diva-6416 (URN)10.1016/j.wear.2008.01.027 (DOI)000258891700050 ()2-s2.0-48049116202 (Scopus ID)
Anmärkning
7th International Conference on Contact Mechanics and Wear of Rail/Wheel Systems Location: Brisbane, AUSTRALIA Date: SEP, 2006Tillgänglig från: 2006-11-22 Skapad: 2006-11-22 Senast uppdaterad: 2017-12-14Bibliografiskt granskad
3. Towards calibrated wheel wear simulation: a comparison between traditional approach and novel methods
Öppna denna publikation i ny flik eller fönster >>Towards calibrated wheel wear simulation: a comparison between traditional approach and novel methods
2004 (Engelska)Ingår i: Proceedings of the 6th International Conference on Railway Bogies and Running Gears, Budapest, September 13-16, 2004., 2004Konferensbidrag, Publicerat paper (Refereegranskat)
Nationell ämneskategori
Farkostteknik
Forskningsämne
Järnvägsgruppen - Fordonsteknik
Identifikatorer
urn:nbn:se:kth:diva-6417 (URN)
Konferens
The 6th International Conference on Railway Bogies and Running Gears, Budapest, September 13-16, 2004
Anmärkning

QC 20110124

Tillgänglig från: 2006-11-22 Skapad: 2006-11-22 Senast uppdaterad: 2016-08-22Bibliografiskt granskad
4. Emerging engineering models for wheel/rail wear simulation
Öppna denna publikation i ny flik eller fönster >>Emerging engineering models for wheel/rail wear simulation
2005 (Engelska)Ingår i: Proceedings of the 8th International Conference Railway Engineering, London, June 29-30, 2005, 2005Konferensbidrag, Publicerat paper (Refereegranskat)
Nationell ämneskategori
Farkostteknik
Forskningsämne
Järnvägsgruppen - Fordonsteknik
Identifikatorer
urn:nbn:se:kth:diva-6418 (URN)
Konferens
The 8th International Conference Railway Engineering, London, June 29-30, 2005
Anmärkning
QC 20110124Tillgänglig från: 2006-11-22 Skapad: 2006-11-22 Senast uppdaterad: 2011-05-06Bibliografiskt granskad
5. Wheel Wear Modelling Including Disc Braking and Contact Environment: Simulation of 18 Months of Commuter Service in Stockholm
Öppna denna publikation i ny flik eller fönster >>Wheel Wear Modelling Including Disc Braking and Contact Environment: Simulation of 18 Months of Commuter Service in Stockholm
2004 (Engelska)Ingår i: Proceedings of the 14th International Wheelset Congress, 2004Konferensbidrag, Publicerat paper (Övrigt vetenskapligt)
Abstract [en]

This paper addresses some aspects of modelling and validation of wheel wear simulation. In previous work at KTH the influences of braking and lubrication have been accounted for through empirically estimated average scaling factors. The current research shows how to include those effects in the set of simulations instead. Disc braking has been included in the simulation set and a wear map for moist contact conditions based on recent tribometer tests has been drafted and tested. Good agreement with measurements from theStockholmcommuter service is achieved. It is concluded that the model improvements accounted for are sufficient for adequate simulation of tread wear but that further development of the flange / gauge corner contact modelling is needed.

Nationell ämneskategori
Farkostteknik
Forskningsämne
Järnvägsgruppen - Fordonsteknik
Identifikatorer
urn:nbn:se:kth:diva-13144 (URN)
Externt samarbete:
Konferens
14th International Wheelset Congress, Orlando, October 17-22, 2004
Anmärkning

QC 20100531

Tillgänglig från: 2010-05-31 Skapad: 2010-05-31 Senast uppdaterad: 2016-09-02Bibliografiskt granskad
6. Proposed procedure and trial simulation of rail profile evolution due to uniform wear
Öppna denna publikation i ny flik eller fönster >>Proposed procedure and trial simulation of rail profile evolution due to uniform wear
2008 (Engelska)Ingår i: Proceedings of the Institution of mechanical engineers. Part F, journal of rail and rapid transit, ISSN 0954-4097, E-ISSN 2041-3017, Vol. 222, nr 1, s. 15-25Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

A procedure for numerical simulation of rail wear and the corresponding profile evolution has been formulated. The wear is assumed to be uniform in the sense that the profiles remain constant along the track portion to be investigated. A simulation set is selected defining the vehicles running on the track, their operating conditions, and contact parameters. Several variations of input data may be included together with the corresponding occurrence probability.

Simulation of multi-body dynamics is used to calculate contact forces and positions, and Archard's wear equation is applied for the calculation of wear depth. Wear coefficients as a function of contact pressure and relative sliding velocity are collected from different test results.

Trial calculations of four non-lubricated and two lubricated curves with radii from 303 to 802 m show qualitatively reasonable results in terms of profile shape development and difference in wear mechanisms between gauge corner and rail head. The wear rates related to traffic tonnage are, however, overestimated and the lubrication efficiency underestimated.

It is expected that model refinements in terms of environmental influence and contact stress calculation are useful to improve the quantitative results.

Nyckelord
rail wear, rail profile, simulation, contact model
Nationell ämneskategori
Farkostteknik
Forskningsämne
Järnvägsgruppen - Fordonsteknik
Identifikatorer
urn:nbn:se:kth:diva-6420 (URN)10.1243/09544097JRRT173 (DOI)000256329800002 ()2-s2.0-43649100269 (Scopus ID)
Anmärkning
QC 20110124.Uppdaterad från submitted till published(20110124)Tillgänglig från: 2006-11-22 Skapad: 2006-11-22 Senast uppdaterad: 2017-12-14Bibliografiskt granskad

Open Access i DiVA

fulltext(8713 kB)4440 nedladdningar
Filinformation
Filnamn FULLTEXT01.pdfFilstorlek 8713 kBChecksumma SHA-1
4ba7ad5fede90b05881c1b3748dd5583525cc291e427fb4f30e92c60d0c6c06dd088c3ae
Typ fulltextMimetyp application/pdf

Personposter BETA

Enblom, Roger

Sök vidare i DiVA

Av författaren/redaktören
Enblom, Roger
Av organisationen
Järnvägsteknik
Farkostteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar
Totalt: 4440 nedladdningar
Antalet nedladdningar är summan av nedladdningar för alla fulltexter. Det kan inkludera t.ex tidigare versioner som nu inte längre är tillgängliga.

isbn
urn-nbn

Altmetricpoäng

isbn
urn-nbn
Totalt: 4327 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf