Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Application of a swirling flow producer in a conventional tundish during continuous casting of steel
KTH, Skolan för industriell teknik och management (ITM), Materialvetenskap.
KTH, Skolan för industriell teknik och management (ITM), Materialvetenskap.
KTH, Skolan för industriell teknik och management (ITM), Materialvetenskap.
KTH, Skolan för industriell teknik och management (ITM), Materialvetenskap.
2017 (Engelska)Ingår i: ISIJ International, ISSN 0915-1559, E-ISSN 1347-5460, Vol. 57, nr 12, s. 2175-2184Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

A swirling flow producer was designed for a conventional tundish in order to produce a swirling flow in the SEN driven by the steel flow potential. CFD simulations were carried out to investigate the flow phenomena in the new tundish system. The results show that a swirling flow in the tundish SEN was successfully obtained. The swirl number of the obtained steel flow inside the SEN can reach a value of 1.34, with a tangential velocity of around 2.8 m/s. The possibility of slag entrainment at the top of the tundish was estimated by analyzing the steel flow characteristics near the top surface. The calculated Weber Number is around 0.3 outside the cylinder, which indicates a low possibility of slag entrainment. A high value of shear stress was found on the SEN wall. This is due to the rotational steel flow in SEN. Also, non-metallic inclusions were tracked in the fully developed steel flow field. It was found that the number of inclusions that touch the top surface increases with an increased inclusion size. Small size inclusions mainly move into the cylinder from the left side of tangential inlet. Therefore, methods like installing a dam at the tundish bottom may be helpful to change the inclusion trajectories to move towards the top of the tundish.

Ort, förlag, år, upplaga, sidor
Iron and Steel Institute of Japan , 2017. Vol. 57, nr 12, s. 2175-2184
Nyckelord [en]
Continuous casting, Slag entrainment, Swirling flow producer, Swirling flow SEN, Tundish design
Nationell ämneskategori
Metallurgi och metalliska material
Identifikatorer
URN: urn:nbn:se:kth:diva-220974DOI: 10.2355/isijinternational.ISIJINT-2017-377ISI: 000418992600012Scopus ID: 2-s2.0-85039788240OAI: oai:DiVA.org:kth-220974DiVA, id: diva2:1172618
Anmärkning

QC 20180110

Tillgänglig från: 2018-01-10 Skapad: 2018-01-10 Senast uppdaterad: 2018-01-16Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltextScopus

Personposter BETA

Ersson, Mikael

Sök vidare i DiVA

Av författaren/redaktören
Ni, PeiyuanJonsson, Lage T. I.Ersson, MikaelJönsson, Pär Göran
Av organisationen
Materialvetenskap
I samma tidskrift
ISIJ International
Metallurgi och metalliska material

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 57 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf