Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
EBSD analysis of surface and bulk microstructure evolution during interrupted tensile testing of a Fe-19Cr-12Ni alloy
Materials Science, Dalarna University, Falun, Sweden.
KTH, Skolan för industriell teknik och management (ITM), Materialvetenskap.
KTH, Skolan för industriell teknik och management (ITM), Materialvetenskap.
Visa övriga samt affilieringar
2018 (Engelska)Ingår i: Materials Characterization, ISSN 1044-5803, E-ISSN 1873-4189, Vol. 141, s. 8-18Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

The microstructure evolution in both surface and bulk grains in a pure Fe-19Cr-12Ni alloy has been analyzed using electron backscatter diffraction after tensile testing interrupted at different strains. Surface grains were studied during in situ tensile testing performed in a scanning electron microscope, whereas bulk grains were studied after conventional tensile testing. The evolution of the deformation structure in surface and bulk grains displays a strong resemblance but the strain needed to obtain a similar deformation structure is lower in the case of surface grains. Both slip and twinning are observed to be important deformation mechanisms, whereas deformation-induced martensite formation is of minor importance. Since the stacking fault energy (SFE) is low, ~17 mJ/m2, dynamic recovery by cross slip of un-dissociated dislocations is unfavorable. This reduces the annihilation of dislocations which in turn leads to a significant increase of low angle boundaries with increasing strain. The low SFE also favors formation of deformation twins which reduces the slip distance, leading to a hardening similar to the Hall-Petch relation. The combination of a low ability for cross-slip and a reduced slip distance caused by twinning is concluded to be the main reason for maintaining a high strain-hardening rate up to strains close to necking.

Ort, förlag, år, upplaga, sidor
2018. Vol. 141, s. 8-18
Nationell ämneskategori
Materialteknik
Identifikatorer
URN: urn:nbn:se:kth:diva-227661DOI: 10.1016/j.matchar.2018.04.035ISI: 000435428100002Scopus ID: 2-s2.0-85046128454OAI: oai:DiVA.org:kth-227661DiVA, id: diva2:1205027
Anmärkning

QC 20180514

Tillgänglig från: 2018-05-09 Skapad: 2018-05-09 Senast uppdaterad: 2018-07-02Bibliografiskt granskad
Ingår i avhandling
1. Experimental Studies of Deformation Structures in Stainless Steels using EBSD
Öppna denna publikation i ny flik eller fönster >>Experimental Studies of Deformation Structures in Stainless Steels using EBSD
2018 (Engelska)Doktorsavhandling, sammanläggning (Övrigt vetenskapligt)
Abstract [en]

In this thesis, the focus has been the study of deformation structures in stainless steels by using electron backscatter diffraction (EBSD). Via increased knowledge of the evolution of the substructure during deformation, the design and control of the manufacturing process can be improved.

A relation was found between the active deformation mechanisms, the evolution of low angle boundaries (LABs) and the strain hardening rate. When deformation twinning was an active deformation mechanism in an austenitic stainless steel with lower stacking fault energy (SFE), the strain hardening rate was maintained up to large strains due to formation of LABs. The deformation twin boundaries acted as new obstacles for dislocation slip which in turn increased the formation of LABs even further. During deformation by slip in an austenitic stainless steel with a higher SFE, the strain hardening rate instead decreased when LABs were formed. A high value of SFE promotes dislocation cross slip which in turn increases annihilation of dislocations leading to a minor increase in LAB formation.

Deformation structures formed in surface grains during in situ tensile tests were found to develop at lower strains than in bulk grains obtained from interrupted conventional tensile tests. This behavior is consistent with the fact that dislocations sources and deformation twinning operate at approximately half the stress on a free surface as compared to the bulk.

The deformation structures were quantified by measuring size distributions for entities bounded by LABs and high angle boundaries (HABs). The size distributions were found to be well described by bimodal lognormal distribution functions. The average size for the distribution of small grains and subgrains correlated well with the mean free distance of dislocation slip and to the strain hardening.

Ort, förlag, år, upplaga, sidor
KTH Royal Institute of Technology, 2018. s. 63
Serie
TRITA-ITM-AVL ; 2018:24
Nyckelord
EBSD, Austenitic stainless steels, Duplex stainless steel, In situ tensile test, Grain boundaries, Grain rotation, Grain size distribution, Texture, Strain hardening, Structure-property relationship, High strain rate, Wire rod rolling, Roll forming
Nationell ämneskategori
Materialteknik
Identifikatorer
urn:nbn:se:kth:diva-227663 (URN)978-91-7729-772-7 (ISBN)
Disputation
2018-06-05, B2, Brinellvägen 23, Stockholm, 10:00 (Svenska)
Opponent
Handledare
Anmärkning

QC 20180514

Tillgänglig från: 2018-05-14 Skapad: 2018-05-09 Senast uppdaterad: 2018-05-14Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltextScopus

Sök vidare i DiVA

Av författaren/redaktören
Yvell, KarinHedström, PeterBorgenstam, Annika
Av organisationen
Materialvetenskap
I samma tidskrift
Materials Characterization
Materialteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 76 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf