Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
The influence of the lode parameter on ductile failure strain in steel
KTH, Skolan för teknikvetenskap (SCI), Hållfasthetslära (Inst.).ORCID-id: 0000-0003-2470-7679
2011 (Engelska)Ingår i: ICM11, 2011, s. 69-75Konferensbidrag, Publicerat paper (Refereegranskat)
Abstract [en]

In this study an experimental investigation was conducted on tensile round circumferentially notched bar specimens. The results were compared to the experimental result on double notched tube specimens subjected to tension and torsion conducted in [5]. The comparison was done for moderate stress triaxiality levels larger than 0.7 with the objective to assess the influence of the Lode parameter on the ductile failure strain. The effective plastic strain, the stress triaxiality T and the Lode parameter L were determined at the center of the notch up to the point of failure by means of finite element based on J2-plasticity. The influence of the Lode parameter on the failure strain was remarkable for the high strength and low hardening material, whereas for the medium strength and high hardening material the influence of the Lode parameter was less prominent. The experimental results were then analyzed with the micromechanical model proposed in [6-7] which is based on the assumption that ductile failure is a consequence of that plastic deformation localizing into a band of imperfections. It is found that the micromechanical model captures the experimental trend and thus the influence of L on the ductility very well. It is found that the Lode parameter sensitivity increases with increase in the yield strength. The fractographical analysis reveals that Lode parameter sensitivity is associated with the failure characteristics of the material.

Ort, förlag, år, upplaga, sidor
2011. s. 69-75
Serie
Procedia Engineering, ISSN 1877-7058 ; 10
Nyckelord [en]
Ductile failure, Experiments, Failure characteristics, Lode parameter, Micromechanics, Stress state, Triaxiality, Void coalescence, Ductile failures, Coalescence, Composite micromechanics, Hardening, Materials, Mechanical engineering, Strength of materials, Plastic deformation
Nationell ämneskategori
Maskinteknik
Identifikatorer
URN: urn:nbn:se:kth:diva-150754DOI: 10.1016/j.proeng.2011.04.014ISI: 000300451300011Scopus ID: 2-s2.0-80052943952OAI: oai:DiVA.org:kth-150754DiVA, id: diva2:744931
Konferens
11th International Conference on the Mechanical Behavior of Materials, ICM11, 5 June 2011 through 9 June 2011, Como
Anmärkning

QC 20140909

Tillgänglig från: 2014-09-09 Skapad: 2014-09-09 Senast uppdaterad: 2014-09-09Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltextScopus

Sök vidare i DiVA

Av författaren/redaktören
Faleskog, Jonas
Av organisationen
Hållfasthetslära (Inst.)
Maskinteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 73 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf