Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Analysis of running-in using Stribeck curves, with application to gear mesh
KTH, Skolan för industriell teknik och management (ITM), Maskinkonstruktion (Inst.), Tribologi. KTH, Skolan för industriell teknik och management (ITM), Maskinkonstruktion (Inst.), Maskinkonstruktion (Avd.).
KTH, Skolan för industriell teknik och management (ITM), Maskinkonstruktion (Inst.), Maskinkonstruktion (Avd.). KTH, Skolan för industriell teknik och management (ITM), Maskinkonstruktion (Inst.), Tribologi.
KTH, Skolan för industriell teknik och management (ITM), Maskinkonstruktion (Inst.), Maskinkonstruktion (Avd.). KTH, Skolan för industriell teknik och management (ITM), Maskinkonstruktion (Inst.), Tribologi.ORCID-id: 0000-0003-2489-0688
(Engelska)Manuskript (preprint) (Övrigt vetenskapligt)
Nyckelord [en]
Running-in, Surface topography, Friction, Lubrication regimes
Nationell ämneskategori
Maskinteknik Tribologi (ytteknik omfattande friktion, nötning och smörjning)
Forskningsämne
Maskinkonstruktion
Identifikatorer
URN: urn:nbn:se:kth:diva-152697OAI: oai:DiVA.org:kth-152697DiVA, id: diva2:751462
Anmärkning

QS 2014

Tillgänglig från: 2014-10-01 Skapad: 2014-10-01 Senast uppdaterad: 2018-01-11Bibliografiskt granskad
Ingår i avhandling
1. Influence of running-in on gear efficiency
Öppna denna publikation i ny flik eller fönster >>Influence of running-in on gear efficiency
2014 (Engelska)Doktorsavhandling, sammanläggning (Övrigt vetenskapligt)
Abstract [en]

The general trend in gear industry is an increased focus on gear transmission efficiency. This thesis focuses on the understanding of how different gear manufacturing methods – particularly the contribution of the running-in process – affect the surface characteristics and friction response, with the purpose of increasing gearbox efficiency. The thesis consists of a summary and five appended papers.

The research hypothesis in paper A and paper B was that the dry elastic contact area ratio is a descriptive parameter for the contact condition. Paper A deals with the influence of manufacturing method on the initial contact conditions. The emphasis in paper B is the changes that occur during running-in and correlating these changes to design requirements. Paper C examines the influence of manganese phosphate coating and lubricants, with respect to friction and the risk of scuffing at the initial contact. Paper D examines the effect of running-in load on the friction response for different surfaces. In paper E, the question of whether the load during running-in influences the gear mesh efficiency is further expounded.

The main conclusions of this thesis are that the running-in influences the gear mesh efficiency; a high running-in load enhances the gear mesh efficiency. The difference in mesh efficiency is in the range of one tenth of a per cent. Thus, the influence of running-in cannot be neglected because it is in the same order of magnitude as reported for other gear efficiency enhancements. Furthermore, the dry elastic contact area ratio presents a descriptive measure of how surface topography influences the contact, at both a global (form deviation) and local (roughness) level. The surface topography caused by the manufacturing method has a significant influence on the contact area ratio. Shaving was found to have the highest contact area ratio, and would therefore be the best choice if deviations from case hardening could be minimised. It was also confirmed that surfaces coated with manganese phosphate raise the limiting load for scuffing failure up to 13 times compared to the uncoated ground equivalent.

Ort, förlag, år, upplaga, sidor
Stockholm: KTH Royal Institute of Technology, 2014. s. 56
Serie
TRITA-MMK, ISSN 1400-1179 ; 2014:09
Nyckelord
gears; gear manufacturing; running-in; efficiency, friction, surface topography
Nationell ämneskategori
Tribologi (ytteknik omfattande friktion, nötning och smörjning)
Forskningsämne
Maskinkonstruktion
Identifikatorer
urn:nbn:se:kth:diva-152699 (URN)978-91-7595-258-1 (ISBN)
Disputation
2014-10-24, Sal B242, Brinellvägen 83, KTH, Stockholm, 10:00 (Engelska)
Opponent
Handledare
Anmärkning

QC 20141002

Tillgänglig från: 2014-10-02 Skapad: 2014-10-01 Senast uppdaterad: 2018-01-11Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Personposter BETA

Olofsson, Ulf

Sök vidare i DiVA

Av författaren/redaktören
Sjöberg, SörenAndersson, MartinOlofsson, Ulf
Av organisationen
TribologiMaskinkonstruktion (Avd.)
MaskinteknikTribologi (ytteknik omfattande friktion, nötning och smörjning)

Sök vidare utanför DiVA

GoogleGoogle Scholar

urn-nbn

Altmetricpoäng

urn-nbn
Totalt: 251 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf