Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Minimal quantity cooling lubrication in turning of Ti6Al4V: Influence on surface roughness, cutting force and tool wear
KTH, Skolan för industriell teknik och management (ITM), Industriell produktion. Amer Univ Sharjah, U Arab Emirates.
KTH, Skolan för industriell teknik och management (ITM), Industriell produktion.ORCID-id: 0000-0002-5960-2159
KTH, Skolan för industriell teknik och management (ITM), Industriell produktion.
2017 (engelsk)Inngår i: Proceedings of the Institution of mechanical engineers. Part B, journal of engineering manufacture, ISSN 0954-4054, E-ISSN 2041-2975, Vol. 231, nr 9, s. 1542-1558Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

Titanium alloys generally show low machinability ratings. They are referred as difficult-to-cut materials due to their inherent properties such as low thermal conductivity, high chemical reactivity and high strength at elevated temperatures. Cooling strategies play an important role to improve the machining performance of the cutting process. In order to facilitate the heat dissipation from the cutting zone, generous amount of coolant is used when machining highly reactive metals such as titanium alloys. Generally, cutting coolants are nominated as pollutants due to their non-biodegradable nature. This article presents experimental evaluation of a minimal quantity cooling lubrication system. The study investigates a combination of sub-zero-temperature air and vegetable oil-based mist as possible environmentally benign alternative to conventional cooling methods. The results are compared with the dry and flood cutting environments as well. Machinability was evaluated experimentally by considering the surface finish, cutting forces, tool life and their associated tool wear mechanisms. It was concluded from the results obtained from the surface roughness, cutting force and tool life investigation that minimal quantity cooling lubrication (internal) cooling strategy has encouraging potential to replace the conventional flood cooling method.

sted, utgiver, år, opplag, sider
Sage Publications, 2017. Vol. 231, nr 9, s. 1542-1558
Emneord [en]
Titanium alloys, minimal quantity cooling lubrication, sustainable machining, lubrication, cooling strategies, tool wear
HSV kategori
Identifikatorer
URN: urn:nbn:se:kth:diva-210999DOI: 10.1177/0954405415599946ISI: 000404030300004Scopus ID: 2-s2.0-85021206613OAI: oai:DiVA.org:kth-210999DiVA, id: diva2:1129765
Merknad

QC 20170807

Tilgjengelig fra: 2017-08-07 Laget: 2017-08-07 Sist oppdatert: 2017-08-07bibliografisk kontrollert

Open Access i DiVA

Fulltekst mangler i DiVA

Andre lenker

Forlagets fulltekstScopus

Personposter BETA

Pervaiz, SalmanRashid, AmirNicolescu, Mihai

Søk i DiVA

Av forfatter/redaktør
Pervaiz, SalmanRashid, AmirNicolescu, Mihai
Av organisasjonen
I samme tidsskrift
Proceedings of the Institution of mechanical engineers. Part B, journal of engineering manufacture

Søk utenfor DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric

doi
urn-nbn
Totalt: 85 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf