Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Characterization of factors interacting in CGI machining: machinability - material microstructure - material physical properties
KTH, Skolan för industriell teknik och management (ITM), Industriell produktion, Maskin- och processteknologi.
2008 (Engelska)Licentiatavhandling, sammanläggning (Övrigt vetenskapligt)
Abstract [en]

The Swedish truck industry is forced to find new material solutions to achieve lighter engines with increased strength. Customers and new environmental regulations demand both higher specific power and more environmentally friendly trucks, and this places a rising pressure on the manufactures. This demand could be met by increasing the peak pressure in the cylinders. Consequently, a more efficient combustion is obtained and the exhaust lowered. This however exposes the engine to higher loads and material physical properties must therefore be enhanced.

Today, alloyed gray iron is the predominantly used engine material. This material cannot meet the requirements of tomorrow’s engines. Compacted Graphite Iron has good potential to be the replacement; it opens new design opportunities with its superior strength, which can lead to smaller, more efficient engines and additional power. The question is: how will manufacturing be affected?

The main goal of this thesis is to identify and investigate the main factors’ effect and their individual contributions on CGI machining.  When the relationship between the fundamental features; machinability, material microstructure, and material physical properties, are revealed, then the CGI material can be optimized, both regarding the manufacturing process and design requirements. The basic understanding is developed mainly through experimental analysis. No attempt has been made to optimize the material to be used as engine material in this thesis.

The thesis demonstrates the importance of having good casting process control. It also illustrates the microstructural properties’ effects on CGI machinability, and what new aspects of machining must be taken into account, compared to gray iron.

Ort, förlag, år, upplaga, sidor
Stockholm: KTH Royal Institute of Technology , 2008. , s. ix, 43
Serie
Trita-IIP, ISSN 1650-1888 ; 08-11
Nyckelord [en]
CGI, Compacted Graphite Iron, milling, cast iron, machinability, material microstructure, material physical properties
Nyckelord [sv]
CGI, kompaktgrafitjärn, fräsning, gjutjärn, skärbarhet, mikrostruktur, materialegenskaper
Nationell ämneskategori
Produktionsteknik, arbetsvetenskap och ergonomi
Identifikatorer
URN: urn:nbn:se:kth:diva-9258ISBN: 978-91-7415-158-9 (tryckt)OAI: oai:DiVA.org:kth-9257DiVA, id: diva2:114189
Presentation
2008-11-14, M311, Brinellsalen, Brinellvägen 68, Stockholm, 10:00 (Svenska)
Opponent
Handledare
Projekt
OPTIMA CGI
Anmärkning
QC 20101105Tillgänglig från: 2008-11-07 Skapad: 2008-10-14 Senast uppdaterad: 2011-05-19Bibliografiskt granskad
Delarbeten
1. Investigation of the Effect of Microstructures on CGI Machining
Öppna denna publikation i ny flik eller fönster >>Investigation of the Effect of Microstructures on CGI Machining
2007 (Engelska)Konferensbidrag, Publicerat paper (Refereegranskat)
Abstract [en]

The aim of this investigation is to evaluate the effect of microstructures on CGI machining and to compare to gray iron reference material. Special designed workpieces, to reproduce real situations, were machined in face milling. The project planning was based on factorial analysis of design of experiments. The results showed that the strongest parameter affecting tool life is the pearlite content. Furthermore it is clear that due to imprecision of manufacturing process it is difficult to obtain test specimens with homogenous microstructures and corresponding varying mechanical properties, when the specimen presents a complex geometrical form. Thin sections found in walls tend to have higher nodularity, resulting in spherical graphite. To refine the investigation of the effect of microstructures on CGI machining it would be preferred to use test specimens without holes or slots to minimise noise in the factor analysis.

Serie
Trita-IIP, ISSN 1650-1888 ; 07-06
Nyckelord
Microstructure, CGI, face milling, machinability, mechanical properties, section effect, cutting forces, tool wear
Nationell ämneskategori
Produktionsteknik, arbetsvetenskap och ergonomi
Identifikatorer
urn:nbn:se:kth:diva-25918 (URN)
Konferens
Swedish Production Symposium, Gothenburg, Sweden, 2007
Anmärkning
QC 20101104Tillgänglig från: 2010-11-04 Skapad: 2010-11-04 Senast uppdaterad: 2011-11-21Bibliografiskt granskad
2. Analysis of Tool Wear in CGI Machining
Öppna denna publikation i ny flik eller fönster >>Analysis of Tool Wear in CGI Machining
2008 (Engelska)Ingår i: IMETI 2008: INTERNATIONAL MULTI-CONFERENCE ON ENGINEERING AND TECHNOLOGICAL INNOVATION, VOL I, PROCEEDINGS, 2008, s. 34-39Konferensbidrag, Publicerat paper (Refereegranskat)
Abstract [en]

In this study the tool wear and wear mechanisms on coated cemented carbide inserts were investigated in turning of Compacted Graphite Iron (CGI) materials with different nodularity. Investigation of how small changes in nodularity affect the wear behaviour of inserts in CGI machining has not earlier been done. The inserts were examined in LOM, SEM and in EDX. The tool wear could on the basis of their wear appearance be classified in three different wear categories; A, B and C. In the wear category A, abrasive wear, adhesive wear and delamination wear could be seen. In the wear category B, the predominant wear mechanism was chipping. The wear appearance in wear category C indicated attrition wear and dissolution via diffusion. Classification of the wear mechanisms gave knowledge that could be used in tool design. The results showed that increasing nodularity has impact on wear at moderate and high cutting speed but not at lower cutting speed. Machining of all materials at high cutting speed, 400 m/min, led to complete degradation of the edge line. A small difference in nodularity from 5% to 20% has more significant impact on wear than from 20% to 62%. This seemed to be correlated with the difference in ultimate tensile strength between the materials.

Serie
Trita-IIP, ISSN 1650-1888 ; 08-07
Nyckelord
Compacted Graphite Iron, machining, tool wear, coated cemented carbides, nodularity
Nationell ämneskategori
Produktionsteknik, arbetsvetenskap och ergonomi
Identifikatorer
urn:nbn:se:kth:diva-25922 (URN)000263828900007 ()2-s2.0-84893180061 (Scopus ID)
Konferens
International Multi-Conference on Engineering and Technological Innovation, Orlando, FL, JUN 29-JUL 02, 2008
Anmärkning
QC 20101105Tillgänglig från: 2010-11-05 Skapad: 2010-11-05 Senast uppdaterad: 2010-11-05Bibliografiskt granskad
3. Analysis of compacted graphite iron machining by investigation of tool temperature and cutting force
Öppna denna publikation i ny flik eller fönster >>Analysis of compacted graphite iron machining by investigation of tool temperature and cutting force
2008 (Engelska)Ingår i: 1st International Conference on Process Machine Interactions: Hannover, Germany, 2008Konferensbidrag, Publicerat paper (Övrigt vetenskapligt)
Serie
Trita-IIP, ISSN 1650-1888 ; 08-08
Nyckelord
Compacted Graphite Iron (CGI), cutting temperature, nodularity, FEM, cutting force
Nationell ämneskategori
Produktionsteknik, arbetsvetenskap och ergonomi
Identifikatorer
urn:nbn:se:kth:diva-25921 (URN)978-3-939026-95-2 (ISBN)
Anmärkning
QC 20101104Tillgänglig från: 2010-11-04 Skapad: 2010-11-04 Senast uppdaterad: 2011-11-21Bibliografiskt granskad

Open Access i DiVA

fulltext(11209 kB)2083 nedladdningar
Filinformation
Filnamn FULLTEXT02.pdfFilstorlek 11209 kBChecksumma SHA-512
982e1b4becde8247b0cc4ab0e609afd94a0e4496a89138cfd0bdf3640589cf1c0dd361334208c7f6b3d59831313ab7459047571c95791ebb6522c2cb6eea7e55
Typ fulltextMimetyp application/pdf

Sök vidare i DiVA

Av författaren/redaktören
Berglund, Anders
Av organisationen
Maskin- och processteknologi
Produktionsteknik, arbetsvetenskap och ergonomi

Sök vidare utanför DiVA

GoogleGoogle Scholar
Totalt: 2088 nedladdningar
Antalet nedladdningar är summan av nedladdningar för alla fulltexter. Det kan inkludera t.ex tidigare versioner som nu inte längre är tillgängliga.

isbn
urn-nbn

Altmetricpoäng

isbn
urn-nbn
Totalt: 1404 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf