Change search
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf
Experimental Analysis on the 'Exact' Cremer Impedance in Rectangular Ducts
KTH, School of Engineering Sciences (SCI), Aeronautical and Vehicle Engineering.
KTH.
KTH, School of Engineering Sciences (SCI), Aeronautical and Vehicle Engineering.ORCID iD: 0000-0001-8099-6554
KTH, School of Engineering Sciences (SCI), Aeronautical and Vehicle Engineering.ORCID iD: 0000-0001-7898-8643
2018 (English)In: SAE technical paper series, ISSN 0148-7191, Vol. 2018-June, no JuneArticle in journal (Refereed) Published
Abstract [en]

Cremer impedance, first proposed by Cremer (Acustica 3, 1953) and then improved by Tester (JSV 28, 1973), refers to the locally reacting boundary condition that can maximize the attenuation of a certain acoustic mode in a uniform waveguide. One limitation in Tester's work is that it simplified the analysis on the effect of flow by only considering high frequencies or the 'well cut-on' modes. This approximation is reasonable for large duct applications, e.g., aero-engines, but not for many other cases of interest, with the vehicle intake and exhaust system included. A recent modification done by Kabral et al. (Acta Acustica united with Acustica 102, 2016) has removed this limitation and investigated the 'exact' solution of Cremer impedance for circular waveguides, which reveals an appreciable difference between the exact and classic solution in the low frequency range. Consequently, the exact solution can lead to a much higher low-frequency attenuation level. In addition, the exact solution is found to exhibit some special properties at very low frequencies, e.g., a negative resistance. In this paper, liners designed on the basis of the exact solution are tested and the difference between the exact and classic solution in the low frequency range (not low enough to go into the negative resistance region) is experimentally investigated.

Place, publisher, year, edition, pages
SAE International , 2018. Vol. 2018-June, no June
National Category
Other Engineering and Technologies
Identifiers
URN: urn:nbn:se:kth:diva-238194DOI: 10.4271/2018-01-1523Scopus ID: 2-s2.0-85050564046OAI: oai:DiVA.org:kth-238194DiVA, id: diva2:1264514
Conference
SAE 10th International Styrian Noise, Vibration and Harshness Congress: The European Automotive Noise Conference, SNVH 2018, Congress GrazSparkassenplatz 1Graz, Austria, 20 June 2018 through 22 June 2018
Note

QC 20181120

Available from: 2018-11-20 Created: 2018-11-20 Last updated: 2019-05-14Bibliographically approved
In thesis
1. Optimal damping and slow sound in ducts
Open this publication in new window or tab >>Optimal damping and slow sound in ducts
2019 (English)Doctoral thesis, comprehensive summary (Other academic)
Abstract [en]

The thesis is dedicated to expanding knowledge on two duct acoustic issues including: 1) the optimal damping of low frequency sound and 2) the development and application of ‘slow sound’.

To address the first issue, the ‘Cremer impedance’ proposed more than half a century ago has been revisited and further developed. The original motivation is to extend the concept from large duct applications, such as aero-engines, to low frequency applications including vehicle intake and exhaust or cooling and ventilation systems. This leads to the derivation of the ‘exact’ solution of the Cremer impedance for single-lined rectangular ducts valid in the low frequency range in the presence of a ‘plug’ flow. A substantial improvement in the low frequency damping is achieved with the exact solution and a measurement campaign is carried out to validate this.

However, for both circular and rectangular ducts (including single-lined and double-lined types) the exact solution of the Cremer impedance has a negative real part in the low frequency range. This indicates that an active boundary is required to provide the optimal damping. Two investigations on the negative resistance are conducted. First, the ‘plug’ flow is replaced by a sheared flow by changing the boundary condition in the optimization model. With this modification, the Cremer impedance is recalculated and the negative resistance is still found in most cases, demonstrating that the negative resistance is not necessarily an artefact of the boundary condition. Second, since the Cremer impedance is based on mode-merging, a mode-merging analysis is carried out. The merging result shows that the downstream results are always valid, but some of the upstream results in the low frequency range are invalid in the sense that unexpected mode pairs merge, and the corresponding damping is smaller than expected. This finding is true for both the fundamental mode and higher order modes.

Regarding the second issue, ‘slow sound’ or sound with a much reduced ‘phase velocity’ is investigated using a resonant periodic system in the low frequency range. This can be seen as an acoustic metamaterial where sound propagates at a much smaller-than-normal speed around its resonance frequency. Following a hydrodynamic particle agglomeration model, the slow sound is applied to manipulate the distribution of small particles in the vehicle exhaust system. Although in principle this acoustic agglomeration method can work, it will only be efficient if the wave damping in the metamaterial is kept small. 

Abstract [sv]

Denna avhandling har till syfte att öka kunskapen om akustiska problem i kanaler, inklusive: 1) optimal dämpning av lågfrekvent ljud och; 2) utveckling och tillämpning av ‘slow sound’.När det gäller det första problemet, har ‘Cremer-impedansen’, som föreslogs för mer än ett halvt sekel sedan studerats och vidareutvecklats. Detta möjliggör nya tillämpningar svarande mot lågfrekvent ljud som insugnings- och avgassystem för fordon samt ventilationssystem. En ‘exakt’ lösning av Cremer-impedansen för rektangulära kanaler med en ljuddämpande vägg giltig i lågfrekvensområdet har härletts. En väsentlig förbättring av lågfrekvent dämpning har uppnåtts med denna lösning vilket även validerats med mätningar.Emellertid har den exakta lösningen av Cremer-impedansen en negativ realdel (‘resistans’) i lågfrekvensområdet, vilket betyder att en aktiv väggbeklädnad är nödvändig för att åstadkomma optimal dämpning. Två undersökningar av den negativa resistansen har genomförts för att studera om dessa lösningar är realiserbara. I den första ändrades randvillkoret för att inkludera gränsskikt i strömningen. Resultatet visade att negativ resistans erhålls i de flesta fall även med det modifierade randvillkoret. I den andra studerades lösningens giltighet i det komplexa vågtalsplanet. Resultatet visade att lösningen nedströms alltid är giltig medan vissa lösningar uppströms i lågfrekvensområdet är ogiltiga. Detta resultat gäller i princip för alla vågor eller moder i en kanal.När det gäller det andra problemet undersöktes möjligheterna att skapa ‘slow sound’, dvs ljud som utbreder sig mycket långsammare än normalt, genom att utnyttja ett resonant periodiskt system i en kanal i lågfrekvensområdet. Detta kan ses som ett s.k. akustiskt metamaterial och kan nyttjas för att med hjälp av starka ljudvågor påverka små partiklar som tvingas att kollidera och bli större. En studie om denna metod för sammanslagning av partiklar (‘particle agglomeration’) kan nyttjas för avgasrening har genomförts. Metoden är teoretiskt möjlig men begränsad av att tekniken för att skapa ‘slow sound’ inte bara saktar ned ljudvågen utan även dämpar dess amplitud och därigenom minska ljudvågens påverkan på partiklar.

Place, publisher, year, edition, pages
KTH Royal Institute of Technology, 2019. p. 75
Series
TRITA-SCI-FOU ; 2019:22
National Category
Fluid Mechanics and Acoustics
Research subject
Vehicle and Maritime Engineering
Identifiers
urn:nbn:se:kth:diva-251443 (URN)978-91-7873-176-3 (ISBN)
Public defence
2019-06-04, F3, Lindstedtsvägen 26, Stockholm, 10:15 (English)
Opponent
Supervisors
Note

QC20190514

Available from: 2019-05-14 Created: 2019-05-14 Last updated: 2019-05-14Bibliographically approved

Open Access in DiVA

No full text in DiVA

Other links

Publisher's full textScopus

Authority records BETA

Zhang, ZhePeerlings, LuckÅbom, Mats

Search in DiVA

By author/editor
Zhang, ZheTiikoja, HeikiPeerlings, LuckÅbom, Mats
By organisation
Aeronautical and Vehicle EngineeringKTH
In the same journal
SAE technical paper series
Other Engineering and Technologies

Search outside of DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric score

doi
urn-nbn
Total: 26 hits
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf