Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
On the interply friction of different generations of unidirectional prepreg materials
KTH, Skolan för teknikvetenskap (SCI), Farkost och flyg, Lättkonstruktioner.
KTH, Skolan för teknikvetenskap (SCI), Farkost och flyg, Lättkonstruktioner.ORCID-id: 0000-0002-6616-2964
2008 (engelsk)Inngår i: Proceedings of 13th European Conference on Composite Materials (ECCM 13), 2008Konferansepaper, Publicerat paper (Fagfellevurdert)
Abstract [en]

With the aim of reducing cost of prepreg composite components, manufacturing methods are developed and refined. An automatic tape laying machine can shorten the process cycle by stacking prepreg flat and thereafter allow for forming into desired shapes. Forming of stacked prepreg requires knowledge about the uncured properties of prepreg, such as viscosity of the matrix, intra- and interply deformation properties. This study focuses on the interply friction, i.e. the friction at the prepreg-prepreg interface, and how this affects the forming. The conclusions presented here show that the difference between prepreg material systems is significant. Further, it is concluded that the prepreg-prepreg friction is governed by a combination of Coulomb and hydrodynamic friction, where different mechanical phenomena dominate depending on the test conditions.

sted, utgiver, år, opplag, sider
2008.
Emneord [en]
prepreg, interply, friction
HSV kategori
Forskningsprogram
SRA - Produktion
Identifikatorer
URN: urn:nbn:se:kth:diva-10679OAI: oai:DiVA.org:kth-10679DiVA, id: diva2:224715
Konferanse
ECCM13: 13th European Conference on Composite Materials, 2 - 5 June 2008, Stockholm, Sweden
Prosjekter
Kostnadseffektiva kompositer (KEKS)
Forskningsfinansiär
XPRES - Initiative for excellence in production research
Merknad

QC 20101015

Tilgjengelig fra: 2013-01-28 Laget: 2009-06-22 Sist oppdatert: 2016-08-11bibliografisk kontrollert
Inngår i avhandling
1. Deformability of unidirectional prepreg materials
Åpne denne publikasjonen i ny fane eller vindu >>Deformability of unidirectional prepreg materials
2009 (engelsk)Licentiatavhandling, med artikler (Annet vitenskapelig)
Abstract [en]

 To reduce cost of structural composites the development of more efficient manufacturing methods is of great interest. Sheet forming of thermoset prepreg, also known as hot drape forming, has been a promising manufacturing method for decades. An automatic tape layer (ATL) can be used to perform the lay-up in an efficient way. The flatly stacked unidirectional prepreg forms a sheet to be formed over a given mould. Knowledge about the materials forming behaviour is important to reach the required shape without flaws, such as wrinkles.

An experimental approach is developed to investigate the intra- (within the layer) and interply deformation. The intraply deformation properties are registered by the use of a bias-extension test and a digital image correlation (DIC) equipment. To measure the interlaminar (between the layers) friction in the prepreg/prepreg interface a specialized rig is designed and built.

The two tested materials are Cycom® HTA/977-2 from Cytec and HexPly® T700/M21 from Hexel, which are examples of the second and third generation of carbon fibre/epoxy prepreg. Where M21 includes craze stoppers in form of thermoplastic particles, the 977-2 has the same function but in melted stage. These particles seem to influence both the intraply deformation modes and increase the level of friction between layers.

The results from the bias-extension test was compared with the theory of pin-jointed net (PJN) and it was found that M21 behaves accordingly. The measured rotation for 977-2 is less than the theoretical, this due to slippage. The rate of deformation seems to have an influence not only on the load level, but also in the mode of deformation. Both for the interlaminar and intraply deformation the resistance to motion were much larger for M21 than 977-2.

sted, utgiver, år, opplag, sider
Stockholm: KTH, 2009. s. 25
Serie
Trita-AVE, ISSN 1651-7660 ; 2009:32
Emneord
prepreg, deformability, carbon composite
HSV kategori
Identifikatorer
urn:nbn:se:kth:diva-10681 (URN)
Presentation
2009-06-12, H1, Teknikringen 33, KTH, Stockholm, 13:15 (svensk)
Opponent
Veileder
Prosjekter
KEKS (kostnadseffektiva kompositer)
Tilgjengelig fra: 2009-06-24 Laget: 2009-06-23 Sist oppdatert: 2012-09-19bibliografisk kontrollert

Open Access i DiVA

fulltext(295 kB)107 nedlastinger
Filinformasjon
Fil FULLTEXT01.pdfFilstørrelse 295 kBChecksum SHA-512
c8ddd5414818579746294c24457119c2da533d5b8a1fb57e32203001ea61789ea264b98cfb625b191c173c288f6cd6e046a3563b477eeeaa562789d49da92b8c
Type fulltextMimetype application/pdf

Andre lenker

http://extra.ivf.se/eccm13_programme/abstracts/1723.pdf

Personposter BETA

Åkermo, Malin

Søk i DiVA

Av forfatter/redaktør
Larberg, YlvaÅkermo, Malin
Av organisasjonen

Søk utenfor DiVA

GoogleGoogle Scholar
Totalt: 107 nedlastinger
Antall nedlastinger er summen av alle nedlastinger av alle fulltekster. Det kan for eksempel være tidligere versjoner som er ikke lenger tilgjengelige

urn-nbn

Altmetric

urn-nbn
Totalt: 416 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf