Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
An experimental study of the velocity field during filling of an ingot mould
KTH, Tidigare Institutioner, Tillämpad processmetallurgi.ORCID-id: 0000-0003-1919-9964
KTH, Skolan för industriell teknik och management (ITM), Materialvetenskap, Tillämpad processmetallurgi.
KTH, Tidigare Institutioner, Materialvetenskap.
2003 (engelsk)Inngår i: Steel research, ISSN 0177-4832, Vol. 74, nr 7, s. 423-430Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

In the present study the velocity field in a 1:3 scale water model of a 4.2-tonne ingot mould was determined using Laser Doppler Anemometry (LDA). The velocity was measured in the horizontal and vertical directions at several different locations along the centre plane of the model. The effect of different volumetric flow rates and water temperatures was also investigated. The reproducibility of the measurements was found to be satisfactory, since the mean velocity at any measurement location had an average difference of around 10% between two fillings. The effect of different volumetric flow rates showed that while decreasing the flow rate, the mean velocity at the bottom turned from an upward direction to a downward direction. At the top of the model the difference between the mean velocities for the different flow rates was less pronounced. An influence of the temperature on the mean velocity could be observed. However, further studies are required to verify this result.

sted, utgiver, år, opplag, sider
2003. Vol. 74, nr 7, s. 423-430
Emneord [en]
water model, Laser Doppler Anemometry (LDA), ingot casting, fluid flow, velocity field, effect of different volumetric flow rates and water temperatures, water model, molten steel, liquid flow, fluid-flow, gas, powder, bath
HSV kategori
Identifikatorer
URN: urn:nbn:se:kth:diva-22687ISI: 000184288500004OAI: oai:DiVA.org:kth-22687DiVA, id: diva2:341385
Merknad

QC 20100525

NR 20140804Tilgjengelig fra: 2010-08-10 Laget: 2010-08-10 Sist oppdatert: 2017-12-12bibliografisk kontrollert

Open Access i DiVA

Fulltekst mangler i DiVA

Søk i DiVA

Av forfatter/redaktør
Tilliander, AndersJonsson, LageJönsson, Pär
Av organisasjonen
I samme tidsskrift
Steel research

Søk utenfor DiVA

GoogleGoogle Scholar

urn-nbn

Altmetric

urn-nbn
Totalt: 257 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf