Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Model films of cellulose II - improved preparation method and characterization of the cellulose film
KTH, Tidigare Institutioner, Fiber- och polymerteknologi.ORCID-id: 0000-0001-8622-0386
2004 (Engelska)Ingår i: Cellulose (London), ISSN 0969-0239, E-ISSN 1572-882X, Vol. 11, nr 2, s. 151-162Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

An optimization study of the preparation of spin-coated cellulose model films from the NMMO/DMSO system on silicon wafers has been made. The study shows that the cellulose concentration in the solution determines the cellulose film thickness and that the temperature of the solution affects the surface roughness. A lower solution temperature results in a lower surface roughness at cellulose concentrations below 0.8%. Using the described method, it is possible to prepare films with thicknesses of 30-90 nm with a constant surface roughness by changing the cellulose concentration, i.e. by dilution with DMSO. On these films, water has a contact angle less than 20degrees and about 50% of the material can, according to CP/MAS C-13-NMR spectroscopy on corresponding fibrous material, be considered to consist of crystalline cellulose II type material. It has further been shown that AFM can be used to determine the thickness of cellulose films, in both dry and wet states. In this method, the difference in height between the top surface and the underlying wafer has been measured at an incision made into the cellulose film. The cellulose films have also been spin-coated with the same technique as on the silicon oxide wafer onto the crystal in a quartz crystal microbalance (QCM). These model films were found to be suitable for swelling measurements with the QCM. The films were very stable during this type of measurement and films with different amounts of charges gave different swelling responses depending on their charges. As expected, films with a higher charge showed a higher swelling.

Ort, förlag, år, upplaga, sidor
2004. Vol. 11, nr 2, s. 151-162
Nyckelord [en]
AFM, coating, contact angle, dissolving pulp, microbalance, microscopy, NMR, spectroscopy, spinning, surfaces, swelling, quartz-crystal microbalance, n-oxide-monohydrate, light-scattering, adsorption, frequency, chloride, kinetics, setup
Nationell ämneskategori
Materialteknik
Identifikatorer
URN: urn:nbn:se:kth:diva-23362DOI: 10.1023/B:CELL.0000025403.23775.75ISI: 000221057300003Scopus ID: 2-s2.0-2942644649OAI: oai:DiVA.org:kth-23362DiVA, id: diva2:342060
Anmärkning

QC 20100525 QC 20111027

Tillgänglig från: 2010-08-10 Skapad: 2010-08-10 Senast uppdaterad: 2017-12-12Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltextScopus

Personposter BETA

Wågberg, LarsLarsson, Per Tomas

Sök vidare i DiVA

Av författaren/redaktören
Wågberg, LarsLarsson, Per Tomas
Av organisationen
Fiber- och polymerteknologi
I samma tidskrift
Cellulose (London)
Materialteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 501 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf