Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Variation in hot metal and stag composition during tapping of blast furnace
KTH, Tidigare Institutioner, Materialvetenskap.
KTH, Tidigare Institutioner, Materialvetenskap.
2004 (Engelska)Ingår i: Ironmaking & steelmaking, ISSN 0301-9233, E-ISSN 1743-2812, Vol. 31, nr 3, s. 216-226Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

To determine the quality of the hot metal and the thermal conditions inside the blast furnace, the composition of the hot metal and slag must be known. Obtaining representative metal and slag samples during tapping is thus highly important to blast furnace operation. The study covered in the present report focused on hot metal and slag composition variation during tapping from a commercial blast furnace. From the results, optimal sampling time points for obtaining elemental concentrations that can be taken as representative for the whole tapping sequence were identified. It was furthermore concluded, that the reliability of hot metal composition data is significantly improved by averaging elemental concentrations determined from two samples, each taken at a particular time point. One sampling, however, was found to be adequate for slag. Results from the study also showed a fairly strong correlation between amounts of silicon and carbon, sulphur and carbon, and silicon and sulphur in the hot metal, while a weaker correlation between hot metal temperature and each of these elements was observed.

Ort, förlag, år, upplaga, sidor
2004. Vol. 31, nr 3, s. 216-226
Nyckelord [en]
hot metal, slag, composition, tapping, blast furnace
Nationell ämneskategori
Metallurgi och metalliska material
Identifikatorer
URN: urn:nbn:se:kth:diva-44830DOI: 10.1179/030192304225018109ISI: 000223335000006Scopus ID: 2-s2.0-4043126824OAI: oai:DiVA.org:kth-44830DiVA, id: diva2:451726
Anmärkning
QC 20111026Tillgänglig från: 2011-10-26 Skapad: 2011-10-25 Senast uppdaterad: 2017-12-08Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltextScopus

Sök vidare i DiVA

Av författaren/redaktören
Andersson, Margareta A. T.Jönsson, Pär G.
Av organisationen
Materialvetenskap
I samma tidskrift
Ironmaking & steelmaking
Metallurgi och metalliska material

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 368 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf