Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Cooling fan noise control using micro-perforates
KTH, Skolan för teknikvetenskap (SCI), Farkost och flyg, MWL Marcus Wallenberg Laboratoriet. KTH, Skolan för industriell teknik och management (ITM), Centra, Competence Center for Gas Exchange (CCGEx).
KTH, Skolan för teknikvetenskap (SCI), Farkost och flyg, MWL Marcus Wallenberg Laboratoriet. KTH, Skolan för industriell teknik och management (ITM), Centra, Competence Center for Gas Exchange (CCGEx).ORCID-id: 0000-0001-7898-8643
2012 (engelsk)Inngår i: Int. Congr. Expos. Noise Control Eng., INTER-NOISE, 2012, s. 10434-10445Konferansepaper, Publicerat paper (Fagfellevurdert)
Abstract [en]

Baffle or split silencers are commonly used, e.g., in HVAC systems and as inlet/outlet silencers on gas turbines. Another application is to reduce noise from the cooling fan inlet for large IC-engines. A baffle silencer can be seen as a periodic arrangement of parallel rectangular absorbers which can be placed in a rectangular duct. The noise reduction afforded by parallel baffles depends not only on the physical properties of the lining, but also upon the angle of incidence of the sound waves impinging and the baffle length. In this paper the potential of using baffles made of Micro-Perforated Panels is investigated in particular with the cooling fan inlet application in mind. Theoretical models for the damping is derived and used to design optimum configurations. The models are based on the wave propagation in a periodic array of baffles so that only one period can be investigated in order to find the different modes. In particular the least attenuated mode is important to find in order to optimize the behavior. An important aspect is the inner structure of the MPP baffle, i.e., can it just be an empty air volume or to what extent must internal waves be prevented by putting in walls. From a stiffness point of view some inner walls might also be needed to avoid vibration problems. Due to these complexities the theoretical models are only presented for the simplest cases. In order to validate the models and to get a more complete test of different designs experiments were also carried out. During these experiments the effect of flow was also tested.

sted, utgiver, år, opplag, sider
2012. s. 10434-10445
Serie
41st International Congress and Exposition on Noise Control Engineering 2012, INTER-NOISE 2012 ; 12
HSV kategori
Identifikatorer
URN: urn:nbn:se:kth:diva-129695Scopus ID: 2-s2.0-84874619913ISBN: 9781627485609 (tryckt)OAI: oai:DiVA.org:kth-129695DiVA, id: diva2:653453
Konferanse
41st International Congress and Exposition on Noise Control Engineering 2012
Merknad

QC 20131004

Tilgjengelig fra: 2013-10-04 Laget: 2013-10-03 Sist oppdatert: 2013-10-04bibliografisk kontrollert

Open Access i DiVA

Fulltekst mangler i DiVA

Scopus

Personposter BETA

Åbom, Mats

Søk i DiVA

Av forfatter/redaktør
Allam, S.Åbom, Mats
Av organisasjonen

Søk utenfor DiVA

GoogleGoogle Scholar

isbn
urn-nbn

Altmetric

isbn
urn-nbn
Totalt: 1276 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf