Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Influence of Tool Materials on Machinability of Titanium- and Nickel-Based Alloys: A Review
KTH, Skolan för industriell teknik och management (ITM), Industriell produktion.
KTH, Skolan för industriell teknik och management (ITM), Industriell produktion.ORCID-id: 0000-0002-5960-2159
KTH, Skolan för industriell teknik och management (ITM), Industriell produktion.
2014 (engelsk)Inngår i: Materials and Manufacturing Processes, ISSN 1042-6914, E-ISSN 1532-2475, Vol. 29, nr 3, s. 219-252Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

Titanium and nickel alloys are the most commonly used in the demanding industries like aerospace, energy, petrochemical, and biomedical. These highly engineered alloys offer unique combination of heat resistance, corrosion resistance, toughness, high operating temperature, and strength-to-weight ratio. These alloys are termed as "Difficult to cut materials" because of their low machinability rating. They are difficult to machine because of properties like low thermal conductivity, high strength at elevated temperatures, and high chemical reactivity. Machining of titanium- and nickel-based alloys causes problems of surface integrity and selection of cutting tool materials that is always a challenge for manufacturers. In this work, machinability studies for titanium and nickel alloys are reviewed with reference to cutting tool materials, associated wear mechanisms, failure modes, and novel tooling techniques. It also discusses major surface integrity defects like carbide cracking, white layer formation, work hardening layer formation, residual stresses, and microstructural alterations. Major aim of this work is to evaluate the challenges involved in improving machinability of the titanium- and nickel-based alloys, and determine the future research direction for productivity improvements in machining these alloys.

sted, utgiver, år, opplag, sider
2014. Vol. 29, nr 3, s. 219-252
Emneord [en]
Nickel, Tools, Machinability, Titanium, Processing, Wear
HSV kategori
Identifikatorer
URN: urn:nbn:se:kth:diva-145092DOI: 10.1080/10426914.2014.880460ISI: 000333997400001Scopus ID: 2-s2.0-84896311946OAI: oai:DiVA.org:kth-145092DiVA, id: diva2:716389
Merknad

QC 20140509

Tilgjengelig fra: 2014-05-09 Laget: 2014-05-08 Sist oppdatert: 2017-12-05bibliografisk kontrollert
Inngår i avhandling
1. Numerical and Experimental Investigations of the Machinability of Ti6AI4V: Energy Efficiency and Sustainable Cooling/ Lubrication Strategies
Åpne denne publikasjonen i ny fane eller vindu >>Numerical and Experimental Investigations of the Machinability of Ti6AI4V: Energy Efficiency and Sustainable Cooling/ Lubrication Strategies
2015 (engelsk)Doktoravhandling, med artikler (Annet vitenskapelig)
Abstract [en]

Titanium alloys are widely utilized in the aerospace, biomedical,marine, petro-chemical and other demanding industries due to theirdurability, high fatigue resistance and ability to sustain elevateoperating temperature. As titanium alloys are difficult to machine, dueto which machining of these alloys ends up with higher environmentalburden. The industry is now embracing the sustainable philosophy inorder to reduce their carbon footprint. This means that the bestsustainable practices have to be used in machining of titanium alloys aswell as in an effort to reduce the carbon footprint and greenhouse gas(GHG) emissions.In this thesis, a better understanding towards the feasibility of shiftingfrom conventional (dry and flood) cooling techniques to the vegetableoil based minimum quantity cooling lubrication (MQCL) wasestablished. Machining performance of MQCL cooling strategies wasencouraging as in most cases the tool life was found close to floodstrategy or sometimes even better. The study revealed that theinfluence of the MQCL (Internal) application method on overallmachining performance was more evident at higher cutting speeds. Inaddition to the experimental machinability investigations, FiniteElement Modeling (FEM) and Computational Fluid Dynamic (CFD)Modeling was also employed to prediction of energy consumed inmachining and cutting temperature distribution on the cutting tool. Allnumerical results were found in close agreement to the experimentaldata. The contribution of the thesis should be of interest to those whowork in the areas of sustainable machining.

sted, utgiver, år, opplag, sider
Stockholm: KTH Royal Institute of Technology, 2015. s. xx, 136
Serie
TRITA-IIP, ISSN 1650-1888 ; 15:07
Emneord
Titanium alloys, Energy consumption, Wear mechanisms, Finite element analysis, computational fluid dynamic analysis
HSV kategori
Forskningsprogram
Industriell produktion
Identifikatorer
urn:nbn:se:kth:diva-173594 (URN)978-91-7595-702-9 (ISBN)
Disputas
2015-10-01, Brinellsal M311, Brinellvägen 68, KTH, Stockholm, 10:00 (engelsk)
Opponent
Veileder
Merknad

QC 20150915

Tilgjengelig fra: 2015-09-15 Laget: 2015-09-15 Sist oppdatert: 2015-09-15bibliografisk kontrollert

Open Access i DiVA

Fulltekst mangler i DiVA

Andre lenker

Forlagets fulltekstScopus

Personposter BETA

Rashid, Amir

Søk i DiVA

Av forfatter/redaktør
Pervaiz, SalmanRashid, AmirNicolescu, Mihai
Av organisasjonen
I samme tidsskrift
Materials and Manufacturing Processes

Søk utenfor DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric

doi
urn-nbn
Totalt: 162 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf