Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Dynamic analysis of soil-steel composite railway bridges: FE-modeling in Plaxis
KTH, Skolan för arkitektur och samhällsbyggnad (ABE), Byggvetenskap, Bro- och stålbyggnad.
KTH, Skolan för arkitektur och samhällsbyggnad (ABE), Byggvetenskap, Bro- och stålbyggnad.
2014 (Engelska)Självständigt arbete på avancerad nivå (masterexamen), 20 poäng / 30 hpStudentuppsats (Examensarbete)
Abstract [en]

A soil-steel composite bridge is a structure comprised of corrugated steel plates, which are joined with bolted connections, enclosed in friction soil material on both sides and on the top. The surrounding friction soil material, or backfill, is applied in sequential steps, each step involving compaction of the soil, which is a necessity for the construction to accumulate the required bearing capacity. Soil-steel composite bridges are an attractive option as compared with other more customary bridge types, owing to the lower construction time and building cost involved. This is particularly true in cases where gaps in the form of minor watercourses, roads or railways must be bridged.

The objective of this master thesis is the modelling of an existing soil-steel composite railway bridge in Märsta, Sweden with the finite element software Plaxis. A 3D model is created and calibrated for crown deflection against measurement data collected by the Division of Structural Engineering and Bridges of the Royal Institute of Technology (KTH) in Stockholm, Sweden.

Once the 3D model is calibrated for deflection, two 2D models with different properties are created in much the same way. In model 1, the full axle load is used and the soil stiffness varied, and in model 2 the soil stiffness acquired in the 3D model is used and the external load varied. The results are compared to measurement data. In 2D model 1 an efficient width of 1,46 m for the soil stiffness is used in combination with the full axle load, and in 2D model 2 an efficient width of 2,85 m is used for the external load, in combination with the soil stiffness acquired in the 3D model.

Aside from this, parametric studies are performed in order to analyse the effect of certain input parameters upon output results, and in order to analyse influence line lengths.

Recreating the accelerations and stresses in the existing bridge using finite element models is complicated, and the results reflect this. Below are shown the discrepancies between model results and measurement data for the pipe crown. The scatter in the measurement data has not been taken into consideration for this; these specific numbers are valid only for one particular train passage.

For crown deflection, the 3D model shows a discrepancy of 4%, 2D model 1 5% and 2D model 2 8% compared with measurement data. For crown acceleration, in the same order, the discrepancy with measurements is 1%, 71% and 21% for maximum acceleration, and 46%, 35% and 28% for minimum acceleration. For maximum crown tensile stress, the discrepancy is 95%, 263% and 13%. For maximum crown compressive stress, the discrepancy is 70%, 16% and 46%.

Ort, förlag, år, upplaga, sidor
2014. , s. 117
Serie
TRITA-BKN-Examensarbete, ISSN 1103-4297 ; 436
Nyckelord [en]
Soil-steel composite bridge; Corrugated steel culvert; High-speed railways; FEM; Plaxis; Field measurements
Nationell ämneskategori
Infrastrukturteknik
Identifikatorer
URN: urn:nbn:se:kth:diva-155515OAI: oai:DiVA.org:kth-155515DiVA, id: diva2:761372
Ämne / kurs
Brobyggnad
Utbildningsprogram
Skolan för arkitektur och samhällsbyggnad (ABE) - Civilingengörsexamen
Presentation
2014-06-05, Projekthallen, Brinellvägen 23, Stockholm, 13:00 (Engelska)
Handledare
Examinatorer
Tillgänglig från: 2014-11-06 Skapad: 2014-11-06 Senast uppdaterad: 2014-11-06Bibliografiskt granskad

Open Access i DiVA

fulltext(11313 kB)2816 nedladdningar
Filinformation
Filnamn FULLTEXT01.pdfFilstorlek 11313 kBChecksumma SHA-512
0d33cde0f9aca90410eb2f50c46b8618d1385b197d9280adf1050cf8607f433982e5ec41fa54f30bcbe67bce427019f2bbebd6f06bafab710390ed93ca3831cf
Typ fulltextMimetyp application/pdf

Sök vidare i DiVA

Av författaren/redaktören
Aagah, OrodAryannejad, Siavash
Av organisationen
Bro- och stålbyggnad
Infrastrukturteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar
Totalt: 2816 nedladdningar
Antalet nedladdningar är summan av nedladdningar för alla fulltexter. Det kan inkludera t.ex tidigare versioner som nu inte längre är tillgängliga.

urn-nbn

Altmetricpoäng

urn-nbn
Totalt: 6186 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf