Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
The influence of finite sample size on surface impedance determination of materials with low sound absorpsion at low frequencies
KTH, Skolan för teknikvetenskap (SCI), Farkost och flyg, MWL Marcus Wallenberg Laboratoriet.ORCID-id: 0000-0003-1604-8263
KTH, Skolan för teknikvetenskap (SCI), Farkost och flyg, MWL Marcus Wallenberg Laboratoriet.ORCID-id: 0000-0003-4103-0129
KTH, Skolan för teknikvetenskap (SCI), Farkost och flyg, MWL Marcus Wallenberg Laboratoriet.ORCID-id: 0000-0002-3826-3055
2015 (Engelska)Konferensbidrag, Publicerat paper (Refereegranskat)
Abstract [en]

The most common noise reducing measure is to add sound absorbing material on the domain boundaries. The boundaries covered by the material may in sumilations be represented by the surface impedance of the material. The impedance can either be modeled or determined experimentally. The experimental determination can be done by the well known standing wave tube method or by a free field method. These free field methods enable impedance determination at any angle of incidence for bulk reacting materials, as opposed to the standing wave tube method that is restricted to normal incidence or locally reacting materials. The method prescribes a point source above the surface and measurements in two points close to the sample surface. From this, the surface impedance can be deduced through the known sound field formulation. Among other things, the impact on the accuracy of the method from the field formulation, signal conditioning and sensor type have been studied in previous work. One major concern is the finite size of the material sample, and its influence on the measurement accuracy. This has previously been investigated for highly absorbing materials and it was shown to be a low frequency problem. Therefore, we focus on the impact of the finite sample in frequencies below 2 kHz. In particular, we relate the magnitude of the impact to the properties of the tested material. Also, the influence of the mounting of the material is analyzed. The study is made through analyzing numerical simulations of the experiment for a variety of setups and materials. Theoretical discussion is provided for deeper understanding of the results. The impact of the finite sample is seen to depend on the material properties, not only the setup as previously shown. Materials with high absorption are shown to be more sensitive to these errors.

Ort, förlag, år, upplaga, sidor
2015.
Nationell ämneskategori
Strömningsmekanik och akustik
Identifikatorer
URN: urn:nbn:se:kth:diva-181690OAI: oai:DiVA.org:kth-181690DiVA, id: diva2:899690
Konferens
Euronoise 2015, the 10th European Congress and Exposition on Noise Control Engineering, Maastricht, Netherlands, 2015-06-01
Anmärkning

QC 20160225

Tillgänglig från: 2016-02-02 Skapad: 2016-02-02 Senast uppdaterad: 2016-02-25Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Personposter BETA

Färm, AnnaBoij, SusannGlav, Ragnar

Sök vidare i DiVA

Av författaren/redaktören
Färm, AnnaBoij, SusannGlav, Ragnar
Av organisationen
MWL Marcus Wallenberg Laboratoriet
Strömningsmekanik och akustik

Sök vidare utanför DiVA

GoogleGoogle Scholar

urn-nbn

Altmetricpoäng

urn-nbn
Totalt: 86 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf