Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Possibility of Sulfur Removal from Ladle Slag by Oxidation in the Temperature Range 1373-1673 K
KTH, Skolan för industriell teknik och management (ITM), Materialvetenskap, Mikro-modellering.ORCID-id: 0000-0001-5080-8401
2015 (Engelska)Ingår i: Journal of Sustainable Metallurgy, ISSN 2199-3823, Vol. 1, nr 3, s. 229-239Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

Experiments were conducted to investigate the possibility of removing sulfur from used ladle slag by oxidation. Slag samples (solid, two-phase mixture, and liquid with a small fraction of solid MgO particles) were subjected to an oxygen-rich atmosphere in the temperature range 1373–1673 K. The sulfur removal from the samples of solid and two-phase mixture was found to be a slow process due to the slow diffusion. The sulfur removal was found to have little dependence on temperature in the range 1373–1573 K. When the slag was mostly liquid (at 1673 K), the sulfur removal was significantly increased. More than 85 % of the sulfur could be removed after 60 min of oxidation in pure oxygen. An increase in oxygen partial pressure was found to increase the desulfurization slightly. Increasing the Al2O3 content in the slag decreased the degree of sulfur removal.

Ort, förlag, år, upplaga, sidor
2015. Vol. 1, nr 3, s. 229-239
Nationell ämneskategori
Metallurgi och metalliska material
Identifikatorer
URN: urn:nbn:se:kth:diva-182833DOI: 10.1007/s40831-015-0018-4OAI: oai:DiVA.org:kth-182833DiVA, id: diva2:906029
Anmärkning

QC 20160229

Tillgänglig från: 2016-02-23 Skapad: 2016-02-23 Senast uppdaterad: 2016-02-29Bibliografiskt granskad
Ingår i avhandling
1. Sulfur and nitrogen in ladle slag
Öppna denna publikation i ny flik eller fönster >>Sulfur and nitrogen in ladle slag
2016 (Engelska)Doktorsavhandling, sammanläggning (Övrigt vetenskapligt)
Abstract [en]

The present work deals with some aspects of slags related to secondary metallurgy in the steelmaking process. More specifically the focus is given to sulfur and nitrogen in ladle slags. Even though slags have been fairly well-researched in the past, the available data for these elements in typical ladle slag compositions is rather scarce. In some cases the available data is in discordance. There are also inconsistencies between the literature data and what is commonly observed in the industrial processes.

Sulfide capacities were measured at steelmaking temperatures, 1823–1873 K, in ladle slags. The data was found to be in reasonable agreement with the industrial process norms. The sulfide capacity was found to increase with the basic oxides CaO and MgO; and decrease with the acidic components Al2O3 and SiO2. The sulfide capacity was also found to increase with temperature.

The dependence of sulfide capacity on the oxygen partial pressure, for slags containing multivalent elements, was investigated experimentally at 1873 K with a slag containing vanadium oxide. A strong dependence of oxygen partial pressure was observed. The sulfide capacity increase by more than two orders of magnitude when the oxygen partial pressure was increased from 4.6×10-16 atm to 9.7×10-10 atm.

The nitrogen solubility and the effect of carbon was investigated in typical ladle slags and the CaO–MgO–SiO2 system at 1873 K. Carbon increases the nitrogen solubility substantially. In the absence of carbon, the nitrogen solubility is extremely low. Low concentrations of cyanide was detected in the carbon saturated slag. This was much lower than the total nitrogen content and formation of cyanide cannot explain the large increase.

The possibility of removing sulfur with oxidation from used ladle slag was investigated experimentally at 1373–1673 K. The sulfur removal of mostly solid slag was found to be a slow process, and would not suitable for industrial practice. At 1673 K the slag was mostly liquid and more than 85% of the sulfur was removed after 60 min of oxidation in pure oxygen atmosphere.

 

Ort, förlag, år, upplaga, sidor
Stockholm: KTH Royal Institute of Technology, 2016. s. vi, 74
Nationell ämneskategori
Metallurgi och metalliska material
Forskningsämne
Teknisk materialvetenskap
Identifikatorer
urn:nbn:se:kth:diva-182981 (URN)978-91-7595-845-3 (ISBN)
Disputation
2016-04-01, Sal F3, Lindstedtsvägen 26, KTH, Stockholm, 10:00 (Engelska)
Opponent
Handledare
Anmärkning

QC 20160229

Tillgänglig från: 2016-02-26 Skapad: 2016-02-24 Senast uppdaterad: 2016-02-29Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltext

Personposter BETA

Allertz, CarlDu, Sichen

Sök vidare i DiVA

Av författaren/redaktören
Allertz, CarlDu, Sichen
Av organisationen
Mikro-modellering
Metallurgi och metalliska material

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 340 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf