Change search
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf
Thermomechanical performance of CFRP synchronizer friction liners
KTH, School of Industrial Engineering and Management (ITM), Machine Design (Dept.).ORCID iD: 0000-0002-6644-7441
KTH, School of Industrial Engineering and Management (ITM).
KTH, School of Industrial Engineering and Management (ITM), Machine Design (Dept.).ORCID iD: 0000-0002-2578-9453
(English)Manuscript (preprint) (Other academic)
Abstract [en]

To improve the ability of a thermomechanical simulation model for CFRP lined synchronizers to predict synchronization performance and reliability, temperature dependent material data for the specific CFRP lining is needed. The compressive modulus, coefficient of thermal expansion, specific heat and thermal conductivity are determined experimentally. The effect of each material property on the focal surface temperature is analyzed, and it is shown that the compressive modulus has the largest influence for all analyzed load cases. Physical tests show that surface hot spots begin to appear at a simulated focal surface temperature of 200 °C, while performance degradation occurs at a simulated focal surface temperature of 230 °C-250 °C.

National Category
Tribology (Interacting Surfaces including Friction, Lubrication and Wear)
Identifiers
URN: urn:nbn:se:kth:diva-237234OAI: oai:DiVA.org:kth-237234DiVA, id: diva2:1258169
Note

QC 20181112

Available from: 2018-10-24 Created: 2018-10-24 Last updated: 2018-11-12Bibliographically approved
In thesis
1. Towards model-based development of heavy truck synchronizers
Open this publication in new window or tab >>Towards model-based development of heavy truck synchronizers
2018 (English)Doctoral thesis, comprehensive summary (Other academic)
Abstract [en]

Gear shifts are becoming more and more important as engines are adapted to low speed and high torque working conditions. Synchronizers are key components for successful gear shifts. To adapt the synchronizers to future engines and thus new working conditions, improved development tools are needed. This thesis includes a comprehensive gear shift and synchronizer frame of reference section with detailed explanations of how a synchronizer works. The thesis also presents two types of numerical models that enable design analyses of the synchronization process.

Fluid-structure interaction models were used to simulate oil evacuation between the synchronizer cones to assess the synchronizer performance during the pre-synchronization phase. For the main synchronization phase, thermomechanical finite element models were used to simulate the transient temperature in the synchronizer contact surfaces. To verify and validate the thermomechanical simulations, both bulk and surface temperature measurements were used, as well as a qualitative comparison of the position of initial wear marks relative to the position of high surface temperature areas in the simulation. The validated thermomechanical model was used to predict failure in molybdenum coated synchronizers. It was shown that the simulated temperature is a better predictor of synchronizer failure than the commonly used parameters “synchronization energy” and “synchronization power”.

A methodology to develop friction models based on sliding speed, contact pressure and surface temperature was developed, and applied for a molybdenum coated synchronizer.

To allow for improved accuracy of carbon fiber reinforced polymer (CFRP) lined synchronizer simulations, material data for a CFRP friction lining was estimated with different test methods. A contact surface temperature threshold where a reduction in coefficient of friction, accelerated wear and formation of hot spots starts was identified.

To reduce the maximum surface temperature, a relative angle between the cone contact surfaces can be introduced. The optimum relative cone angle was determined based on measured geometric deviations for a population of manufactured synchronizers. It was shown that there is an optimum relative cone angle that significantly can reduce the maximum surface temperature during synchronization.

Place, publisher, year, edition, pages
KTH Royal Institute of Technology, 2018. p. 94
Series
TRITA-ITM-AVL ; 2018:51
Keywords
synchronization, synchronizers, gear shift, gearbox
National Category
Tribology (Interacting Surfaces including Friction, Lubrication and Wear)
Identifiers
urn:nbn:se:kth:diva-237235 (URN)978-91-7873-002-5 (ISBN)
Public defence
2018-11-22, Gladan (B319), Brinellvägen 85, holm, 10:00 (English)
Opponent
Supervisors
Funder
VINNOVA, 2112-04619
Available from: 2018-10-24 Created: 2018-10-24 Last updated: 2018-10-24Bibliographically approved

Open Access in DiVA

No full text in DiVA

Authority records BETA

Häggström, DanielSellgren, UlfBjörklund, Stefan

Search in DiVA

By author/editor
Häggström, DanielSellgren, UlfBjörklund, Stefan
By organisation
Machine Design (Dept.)School of Industrial Engineering and Management (ITM)
Tribology (Interacting Surfaces including Friction, Lubrication and Wear)

Search outside of DiVA

GoogleGoogle Scholar

urn-nbn

Altmetric score

urn-nbn
Total: 31 hits
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf