Change search
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf
Monotonic and Cyclic Creep of Cast Materials for Exhaust Manifolds
KTH, School of Industrial Engineering and Management (ITM).ORCID iD: 0000-0001-8673-9073
Volkswagen AG, Wolfsburg, Germany..
Scania, Helsingborg, Sweden..
KTH, School of Industrial Engineering and Management (ITM), Materials Science and Engineering.
2019 (English)In: SAE International Journal of Materials & Manufacturing, ISSN 1946-3979, E-ISSN 1946-3987, Vol. 12, no 2, p. 149-162Article in journal (Refereed) Published
Abstract [en]

Cast materials are creep tested between 600 and 900 degrees C using three methods: (i) tensile testing at different strain rates, (ii) stress relaxation during thermal cycling and (iii) traditional creep tests at constant load. Comparisons are made between fast and slow methods and between monotonic and cyclic deformation modes. The tested materials, SiMo51, SiMo1000, Ni-resist D5S and HK30, are used for exhaust manifolds in heavy-duty diesel engines. The fast and cheap methods, (i) and (ii), were used on all materials, while the tedious and costly method, (iii), was used on SiMo51 only. The creep rates from monotonic tensile tests and stress relaxations during thermal cycling agree well. There is no difference between monotonic and cyclic creep rates, and cyclic rates are practically unchanged with the number of thermal cycles. No or small differences in creep rates are observed when comparing tension and compression, although three of the materials include large graphite nodules. At 700 degrees C, a Norton plot for SiMo51 shows coinciding results for tensile test and compressive stress relaxations, whereas the minimum creep rates from constant load tests fall one order of magnitude lower, but with the same slope. For all materials, the Norton creep parameters are evaluated with accurate reproduction of the experimental data. For HK30, two sets of parameters are needed because of deformation hardening.

Place, publisher, year, edition, pages
SAE INT , 2019. Vol. 12, no 2, p. 149-162
Keywords [en]
Cast iron, Creep tests, Tensile tests, Cyclic creep
National Category
Materials Engineering
Identifiers
URN: urn:nbn:se:kth:diva-255463DOI: 10.4271/05-12-02-0012ISI: 000473301600006OAI: oai:DiVA.org:kth-255463DiVA, id: diva2:1352399
Note

QC 20190918

Available from: 2019-09-18 Created: 2019-09-18 Last updated: 2019-09-18Bibliographically approved

Open Access in DiVA

No full text in DiVA

Other links

Publisher's full text

Authority records BETA

Jonsson, Stefan

Search in DiVA

By author/editor
Öberg, ChristianJonsson, Stefan
By organisation
School of Industrial Engineering and Management (ITM)Materials Science and Engineering
In the same journal
SAE International Journal of Materials & Manufacturing
Materials Engineering

Search outside of DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric score

doi
urn-nbn
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf