Change search
ReferencesLink to record
Permanent link

Direct link
Wafer-level integration of NiTi shape memory alloy on silicon using Au-Si eutectic bonding
KTH, School of Electrical Engineering (EES), Micro and Nanosystems.
KTH, School of Electrical Engineering (EES), Micro and Nanosystems.
KTH, School of Electrical Engineering (EES), Micro and Nanosystems.
KTH, School of Electrical Engineering (EES), Micro and Nanosystems.ORCID iD: 0000-0001-9552-4234
Show others and affiliations
2013 (English)In: Journal of Micromechanics and Microengineering, ISSN 0960-1317, E-ISSN 1361-6439, Vol. 23, no 1, 1-14 p.Article in journal (Refereed) Published
Abstract [en]

This paper reports on the wafer level integration of NiTi shape memory alloy (SMA) sheets with silicon substrates through Au-Si eutectic bonding. Different bond parameters, such as Au layer thicknesses and substrate surface treatments were evaluated. The amount of gold in the bond interface is the most important parameter to achieve a high bond yield; the amount can be determined by the barrier layers between the Au and Si or by the amount of Au deposition. Deposition of a gold layer of more than 1 mu m thickness before bonding gives the most promising results. Through patterning of the SMA sheet and by limiting bonding to small areas, stresses created by the thermal mismatch between Si and NiTi are reduced. With a gold layer of 1 mu m thickness and bond areas between 200 x 200 and 800 x 800 mu m(2) a high bond strength and a yield above 90% is demonstrated.

Place, publisher, year, edition, pages
2013. Vol. 23, no 1, 1-14 p.
Keyword [en]
Microactuators, Gold, Temperature, Fabrication, Film
National Category
Engineering and Technology
URN: urn:nbn:se:kth:diva-93492DOI: 10.1088/0960-1317/23/1/015008ISI: 000312248200008ScopusID: 2-s2.0-84877969669OAI: diva2:516504
EU, European Research Council, 267528

QC 20130110. Updated from accepted to published.

Available from: 2012-04-18 Created: 2012-04-18 Last updated: 2015-09-30Bibliographically approved
In thesis
1. Heterogeneous Integration of Shape Memory Alloysfor High-Performance Microvalves
Open this publication in new window or tab >>Heterogeneous Integration of Shape Memory Alloysfor High-Performance Microvalves
2012 (English)Doctoral thesis, comprehensive summary (Other academic)
Abstract [en]

This thesis presents methods for fabricating MicroElectroMechanical System (MEMS) actuators and high-flow gas microvalves using wafer-level integration of Shape Memory Alloys (SMAs) in the form of wires and sheets.

The work output per volume of SMA actuators exceeds that of other microactuation mechanisms, such as electrostatic, magnetic and piezoelectric actuation, by more than an order of magnitude, making SMA actuators highly promising for applications requiring high forces and large displacements. The use of SMAs in MEMS has so far been limited, partially due to a lack of cost efficient and reliable wafer-level integration approaches. This thesis presents new methods for wafer-level integration of nickel-titanium SMA sheets and wires. For SMA sheets, a technique for the integration of patterned SMA sheets to silicon wafers using gold-silicon eutectic bonding is demonstrated. A method for selective release of gold-silicon eutectically bonded microstructures by localized electrochemical etching, is also presented. For SMA wires, alignment and placement of NiTi wires is demonstrated forboth a manual approach, using specially built wire frame tools, and a semiautomatic approach, using a commercially available wire bonder. Methods for fixing wires to wafers using either polymers, nickel electroplating or mechanical silicon clamps are also shown. Nickel electroplating offers the most promising permanent fixing technique, since both a strong mechanical and good electrical connection to the wire is achieved during the same process step. Resistively heated microactuators are also fabricated by integrating prestrained SMA wires onto silicon cantilevers. These microactuators exhibit displacements that are among the highest yet reported. The actuators also feature a relatively low power consumption and high reliability during longterm cycling.

New designs for gas microvalves are presented and valves using both SMA sheets and SMA wires for actuation are fabricated. The SMA-sheet microvalve exhibits a pneumatic performance per footprint area, three times higher than that of previous microvalves. The SMA-wire-actuated microvalve also allows control of high gas flows and in addition, offers benefits of lowvoltage actuation and low overall power consumption.

Place, publisher, year, edition, pages
Stockholm: KTH Royal Institute of Technology, 2012. viii, 79 p.
Trita-EE, ISSN 1653-5146 ; 2012:014
Microelectromechanical systems, MEMS, silicon, wafer-level, integration, heterogeneous integration, wafer bonding, Au-Si, eutectic bonding, release etching, electrochemical etching, microvalves, microactuators, shape memory alloy, SMA, NiTinol, TiNi, NiTi, cold-state reset, bias spring, gate valves, wire bonding
National Category
Engineering and Technology
urn:nbn:se:kth:diva-94088 (URN)978-91-7501-304-6 (ISBN)
Public defence
2012-06-01, sal E3, Osquarsbacke 14, KTH, Stockholm, 10:00 (English)
QC 20120514Available from: 2012-05-14 Created: 2012-05-07 Last updated: 2012-05-14Bibliographically approved

Open Access in DiVA

fulltext(6618 kB)30 downloads
File information
File name FULLTEXT01.pdfFile size 6618 kBChecksum SHA-512
Type fulltextMimetype application/pdf

Other links

Publisher's full textScopus

Search in DiVA

By author/editor
Gradin, HenrikBushra, SobiaBraun, StefanStemme, Göranvan der Wijngaart, Wouter
By organisation
Micro and Nanosystems
In the same journal
Journal of Micromechanics and Microengineering
Engineering and Technology

Search outside of DiVA

GoogleGoogle Scholar
Total: 30 downloads
The number of downloads is the sum of all downloads of full texts. It may include eg previous versions that are now no longer available

Altmetric score

Total: 142 hits
ReferencesLink to record
Permanent link

Direct link