Change search
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf
Slag-Steel Equilibrium Calculations by Computational Thermodynamics: Comparison with the Plant Data
KTH, School of Industrial Engineering and Management (ITM), Materials Science and Engineering, Computational Thermodynamics.
(Materials Research and Development, Ovako Hofors AB)
KTH, School of Industrial Engineering and Management (ITM), Materials Science and Engineering, Computational Thermodynamics.ORCID iD: 0000-0001-5031-919X
2011 (English)In: Proceeding of the International Symposium on Liquid Metal Processing and Casting (LMPC 2011), Institut Jean Lamour -Ecole des Mines de Nancy , 2011, 127-134 p.Conference paper, Published paper (Refereed)
Abstract [en]

This study presents a comparison between the measured and calculated results of the slag-steel equilibrium in the ASEA-SKF ladle furnace. The new software LiMeS available with the Thermo-Calc software package was applied in order to calculate the slag-steel equilibrium after the argon degassing process. The input data used in the calculations were those achieved by instrumental analysis of the slag-steel samples that were taken before starting the argon degassing process. The results were compared with the measured values. The calculated Al, Mn and Si contents in the molten steel, and the amounts of Al2O3 and SiO2 in the slag, were in good agreement with the measurements. The calculated and the measured O, S and Mg contents in the molten steel, and the S, CaO and MgO contents of the slag, were not in good agreement. It was concluded that LiMeS is a useful tool for slag-steel equilibrium calculations.

Place, publisher, year, edition, pages
Institut Jean Lamour -Ecole des Mines de Nancy , 2011. 127-134 p.
Keyword [en]
Slag steel equilibrium, Thermo-Calc, LiMeS, Computational thermodynamic
National Category
Metallurgy and Metallic Materials
Identifiers
URN: urn:nbn:se:kth:diva-101464OAI: oai:DiVA.org:kth-101464DiVA: diva2:548206
Conference
International Symposium on Liquid Metal Processing and Casting (LMPC 2011)
Note

QC 20120917

Available from: 2012-08-30 Created: 2012-08-29 Last updated: 2012-09-17Bibliographically approved
In thesis
1. Slag, Steel, Ladle and Non-metallic Inclusions Equilibria in an ASEA-SKF Ladle Furnace
Open this publication in new window or tab >>Slag, Steel, Ladle and Non-metallic Inclusions Equilibria in an ASEA-SKF Ladle Furnace
2012 (English)Doctoral thesis, comprehensive summary (Other academic)
Abstract [en]

This study explores the possibility of prediction and modification of some of the physicochemical properties of non-metallic inclusions by considering top slag-steel-ladle equilibria in an ASEA-SKF ladle furnace. To test the reliability of an available computational thermodynamic computer program, the first sub project was done. It was concluded that LiMeS, an interface for Thermo-Calc, is a useful tool for slag-steel equilibrium calculations. The second sub project was set out to find some model/s that could calculate the most accurate oxygen activity of molten steel compared to the measured one. This study concluded that both Wagner’s and Turkdogan's equations are useful. It was further seen that increasing the Al contents in the molten steel, increasing the CaO/Al2O3 ratio in the top slag, and reducing the temperature, resulted in reduction of the oxygen activity of the molten steel. In the third sub project a comparison was made between measured CaO and Al2O3 (normalised to CaO-Al2O3) in top slag, calcium aluminate inclusions, and the results of theoretical calculations. The average contents of CaO and Al2O3 in all inclusions were close to the composition of the phase Ca12Al14O33 and the contents of CaO and Al2O3 in the slags were close to the composition of the phase Ca3Al2O6 in the binary phase diagram of CaO-Al2O3. The forth sub project set out to study the effect of vacuum degassing time on non-metallic inclusions. It was concluded that during the vacuum degassing process the share of calcium aluminates compared to spinels, Ca content of the oxides, and the average equivalent circle diameters of the oxides were increasing, and oxides tended to form spherical shapes. Finally, based on the preceding four sub projects, the fifth sub project aimed to optimize the steel treatment in an ASEA-SKF ladle furnace. The final results showed that by adding 200 kg fluorite to the top slag of 1200 kg, it was possible to achieve a sulphur content of less than 10 ppm in the steel and a sulphur ratio between slag and steel of 1570, and at the same time reduce the oxygen activity of the molten steel and the degassing time.

Place, publisher, year, edition, pages
Stockholm: KTH Royal Institute of Technology, 2012. xiv, 62 p.
Keyword
Clean steel, Top slag, Non-Metallic Inclusions, Oxides, Vacuum Degassing, Deoxidation, Desulphurization, Equilibrium, Computational Thermodynamics, Scanning electron microscopy
National Category
Metallurgy and Metallic Materials
Identifiers
urn:nbn:se:kth:diva-102149 (URN)978-91-7501-489-0 (ISBN)
Public defence
2012-10-05, sal B2,, Brinellvägen 23, KTH, Stockholm, 13:15 (English)
Opponent
Supervisors
Note

QC 20120917

Available from: 2012-09-17 Created: 2012-09-10 Last updated: 2012-09-18Bibliographically approved

Open Access in DiVA

No full text

Authority records BETA

Selleby, Malin

Search in DiVA

By author/editor
Riyahimalayeri, KamroozSelleby, Malin
By organisation
Computational Thermodynamics
Metallurgy and Metallic Materials

Search outside of DiVA

GoogleGoogle Scholar

urn-nbn

Altmetric score

urn-nbn
Total: 201 hits
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf