Change search
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf
Effect of TurboSwirl on Steel Cleanliness during Ingot Filling
KTH, School of Industrial Engineering and Management (ITM), Materials Science and Engineering, Applied Process Metallurgy.
KTH, School of Industrial Engineering and Management (ITM), Materials Science and Engineering, Applied Process Metallurgy.
KTH, School of Industrial Engineering and Management (ITM), Materials Science and Engineering, Applied Process Metallurgy.
(English)Manuscript (preprint) (Other academic)
National Category
Metallurgy and Metallic Materials
Identifiers
URN: urn:nbn:se:kth:diva-117723OAI: oai:DiVA.org:kth-117723DiVA: diva2:602783
Note

QS 2013

Available from: 2013-02-04 Created: 2013-02-04 Last updated: 2013-02-04Bibliographically approved
In thesis
1. Some Aspects of Improving Initial Filling Conditions and Steel Cleanliness by Flow Pattern Control Using a Swirling Flow in the Uphill Teeming Process
Open this publication in new window or tab >>Some Aspects of Improving Initial Filling Conditions and Steel Cleanliness by Flow Pattern Control Using a Swirling Flow in the Uphill Teeming Process
2013 (English)Doctoral thesis, comprehensive summary (Other academic)
Abstract [en]

The flow pattern has widely been recognized to have an impact on the exogenous non-metallic inclusion generation in the gating system and mold flux entrapment in the uphill teeming process. Thus, a well-controlled flow pattern during the teeming process can improve the quality of ingots and further increase the yield during steel production. The current study focused on investigating and optimizing the flow pattern of steel in the gating system and molds to improve steel cleanliness during the initial filling moment. A mathematical model considering a trumpet was initially compared to a reduced model only considering part of the runner channel. Thereafter, the influence of swirl blades implemented at the bottom of the vertical runner on the improvement of initial filling conditions in the molds was investigated in a model considering the entire mold system including a trumpet. The effects of a swirl blade orientation on a swirling flow were further discussed. The simulation results, when utilizing swirl blades, were also verified by plant trials performed at Scana Steel. In addition, a new novel swirling flow generation component, TurboSwirl, was studied in a model considering the entire mold system including a trumpet. The model was based on modifications of the refractory geometry at the elbow of the runners near the mold without the usage of an inserted flow control device in the gating system. Owing to its great potential for improving the flow pattern of steel during the initial filling moment, the effect of TurboSwirl on steel cleanliness was also studied. The results showed that the initial filling conditions during the uphill teeming process can be improved by using a swirl blade or a TurboSwirl in the gating system. This makes it possible to further decrease the initial position of mold powder bags. In addition, it reduces the possibilities of exogenous non-metallic inclusion generation in the gating system as well as mold flux entrapment in the mold during the uphill teeming process. However, the utilization of swirl blades created a considerable amount of droplets when steel entered the molds during the first couple of seconds, which also was verified by the plant trials. The introduction of TurboSwirl showed a greater potential than a swirl blade due to a more evenly distributed swirling flow. The DPM model adopted in the simulations revealed that the TurboSwirl can improve steel cleanliness by increasing the non-metallic inclusion collision rate both with respect to Stokes and turbulent collisions.

Place, publisher, year, edition, pages
Stockholm: KTH Royal Institute of Technology, 2013. xii,, 61 p.
Keyword
uphill teeming, ingot casting, flow pattern, swirl blade, TurboSwirl, realizable k-ε model, CFD.
National Category
Metallurgy and Metallic Materials
Identifiers
urn:nbn:se:kth:diva-117718 (URN)978-91-7501-596-5 (ISBN)
Public defence
2013-02-22, B1, Brinellvägen 23, KTH, Stockholm, 10:00 (English)
Opponent
Supervisors
Note

QC 20130204

Available from: 2013-02-04 Created: 2013-02-03 Last updated: 2013-02-04Bibliographically approved

Open Access in DiVA

No full text

Search in DiVA

By author/editor
Tan, ZheErsson, MikaelJönsson, Pär G.
By organisation
Applied Process Metallurgy
Metallurgy and Metallic Materials

Search outside of DiVA

GoogleGoogle Scholar

urn-nbn

Altmetric score

urn-nbn
Total: 146 hits
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf