Change search
ReferencesLink to record
Permanent link

Direct link
Statistical Analysis of the Maximum size of Inclusions in Metal Samples
KTH, School of Industrial Engineering and Management (ITM), Materials Science and Engineering, Applied Process Metallurgy.
KTH, School of Industrial Engineering and Management (ITM), Materials Science and Engineering.
KTH, School of Industrial Engineering and Management (ITM), Materials Science and Engineering, Applied Process Metallurgy.
(English)Manuscript (preprint) (Other academic)
Keyword [en]
Clusters, Electrolytic extraction, Non-metallic inclusions, Steel
National Category
Materials Engineering Metallurgy and Metallic Materials
URN: urn:nbn:se:kth:diva-145671OAI: diva2:719511

QS 2014

Available from: 2014-05-26 Created: 2014-05-26 Last updated: 2014-05-26Bibliographically approved
In thesis
1. Three Dimensional Determinations of Inclusions in Ferroalloys and Steel Samples
Open this publication in new window or tab >>Three Dimensional Determinations of Inclusions in Ferroalloys and Steel Samples
2014 (English)Doctoral thesis, comprehensive summary (Other academic)
Abstract [en]

As the requirements on material properties increase, there has been a demand on an additional knowledge on the effect of impurities in the ferroalloyson the steel cleanness. Thus, the number, morphology, size and composition of inclusions in sixdifferent ferroalloys (FeTi, FeNb, FeSi,SiMn, LC and HC FeCr) were investigatedin this study. This was done in three dimensions (3D) by using a SEM in combination with EDS after electrolytic extraction of the ferroalloy samples. Theresults show that thenon-metallic and metallic inclusions can besuccessfully analyzed on the surface of a film filterafter a separation of the inclusions from the matrix. Overall, the inclusions canbe divided into two categories depending on the melting point. Furthermore, the possible transformation of different kinds of inclusions after their addition to the liquid steel canalso be determined.

The inclusions and clusters in steel samples of two similar steel grades of high-silicon non-calcium treated (HSiNC) stainless steels were also investigated and compared during ladle treatment and continuous casting. Samples of liquid steel and slag were taken at different stages of the ladle treatment and casting during two plant trials: a low Al steel (LAl) and a high Al steel (HAl). Spherical (SP), irregular and regular (IR) inclusions and clusters (CL) were observed in the samples from both heats. It wasfound that the morphology and composition of inclusions and clusters in both heats were significantly changed during the ladle treatment and casting. Most of inclusions (44-98%) in a low Al steel are MgO-CaO-SiO2-Al2O3spherical inclusions. The compositions of irregular and regularinclusions and clusters in steel samples of a high Al steel were mostly MgO·Al2O3spinel, but also complex sphericalinclusions containing Al2O3-MgO-CaO-SiO2. In addition, the phase stabilitydiagram based on Darken’s quadratic formalism and Redlich-Kister type polynomial was estimated for both heats at a non-infinite solution.

It is known that clusters in liquid steel have a harmful effect on the casting process and the quality of the final steel product. Therefore, clusters of rare earth metals (REM) were investigated in steel samples of a S30185 stainless steel grade from a pilot trial (PT, 250 kg) and from an industrial heat (IH, 100 t). Samples were taken from the liquid steel at differentholding times after the addition of a mischmetal. The morphology, composition, number and size of clusters in PT and IH steel samples were analyzed and compared as a function of the holding time. It was found that typical clusters with regular and irregular inclusions were the main type of clusters (69%-98%) in all PT and IH steel samples. The composition of inclusions in clusters corresponded mostly to REM-oxides. The size of clusters that were observed in different samples varied mainly from 2 to 23 μm. In addition, the size and number of most clusters in PT are larger than those in IH samples.

Largesize inclusions are recognized to be crucially harmful for the mechanical properties of steel products. Therefore, predictionsof the maximum size of Al2O3-CaO spherical inclusions in an Fe-10 mass% Ni alloy have been examined based on two dimensional (2D) and three dimensional (3D) investigations. The effects of the number of measurements and unit volume on the estimated 3D results were also investigated.

Place, publisher, year, edition, pages
Stockholm: KTH Royal Institute of Technology, 2014. vii, 67 p.
Three dimensional, Ferroalloy, Inclusion, Spinel inclusion, T hermodynamic calculation, REM clusters, Formation mechanism, Statistical analysis, Maximum size
National Category
Metallurgy and Metallic Materials
urn:nbn:se:kth:diva-145225 (URN)978-91-7595-156-0 (ISBN)
Public defence
2014-06-11, Sal B1, Brinellvägen 23, KTH, Stockholm, 10:00 (English)

QC 20140526

Available from: 2014-05-26 Created: 2014-05-14 Last updated: 2014-05-26Bibliographically approved

Open Access in DiVA

No full text

Search in DiVA

By author/editor
Karasev, AndreyBi, YanyanJönsson, Pär G.
By organisation
Applied Process MetallurgyMaterials Science and Engineering
Materials EngineeringMetallurgy and Metallic Materials

Search outside of DiVA

GoogleGoogle Scholar
The number of downloads is the sum of all downloads of full texts. It may include eg previous versions that are now no longer available

Total: 67 hits
ReferencesLink to record
Permanent link

Direct link