Change search
ReferencesLink to record
Permanent link

Direct link
An amperometric nitric oxide sensor with fast response and ppb-level concentration detection relevant to asthma monitoring
KTH, School of Electrical Engineering (EES), Micro and Nanosystems.
KTH, School of Chemical Science and Engineering (CHE), Chemical Engineering and Technology, Applied Electrochemistry.
KTH, School of Electrical Engineering (EES), Micro and Nanosystems.
KTH, School of Electrical Engineering (EES), Micro and Nanosystems.ORCID iD: 0000-0001-9552-4234
Show others and affiliations
2015 (English)In: Sensors and actuators. B, Chemical, ISSN 0925-4005, Vol. 209, 639-644 p.Article in journal (Refereed) Published
Abstract [en]

A MEMS-based amperometric nitric oxide (NO) gas sensor is reported in this paper. The sensor is designed to detect NO gas for the purpose of asthma monitoring. The unique property of this sensor lies in the combination of a microporous high-surface area electrode that is coated with Nafion (TM), together with a liquid electrolyte. The sensor is able to detect gas concentrations of the order of parts-per-billion (ppb) and has a measured NO sensitivity of 0.045 nA/ppb and an operating range between 25 and 65% relative humidity. The settling time of the sensor is measured to 8s. The selectivity to interfering gases such as ammonia (NH3) and carbon monoxide (CO) was high when placing an activated carbon fiber filter above the sensor. The ppb-level detection capability of this sensor combined with its relatively fast response, high selectivity to CO and NH3 makes the sensor potentially applicable in gas monitoring for asthma detection.

Place, publisher, year, edition, pages
2015. Vol. 209, 639-644 p.
Keyword [en]
Nitric oxide, Amperometric, Nafion (TM), MEMS, Gas sensor
National Category
Chemical Sciences Medical Laboratory and Measurements Technologies
URN: urn:nbn:se:kth:diva-161090DOI: 10.1016/j.snb.2014.11.147ISI: 000349082200084ScopusID: 2-s2.0-84919800404OAI: diva2:797838
VINNOVAEU, European Research Council, 267528

QC 20150325

Available from: 2015-03-25 Created: 2015-03-09 Last updated: 2015-09-07Bibliographically approved
In thesis
1. MEMS-based electrochemical gas sensors and wafer-level methods
Open this publication in new window or tab >>MEMS-based electrochemical gas sensors and wafer-level methods
2015 (English)Doctoral thesis, comprehensive summary (Other academic)
Abstract [en]

This thesis describes novel microel ectromechanical system (MEMS) based electrochemical gas sensors and methods of fabrication.

This thesis presents the research in two parts. In the first part, a method to handle a thin silicon wafer using an electrochemically active adhesive is described. Handling of a thin silicon wafer is an important issue in 3D-IC manufacturing where through silicon vias (TSVs) is an enabling technology. Thin silicon wafers are flexible and fragile, therefore difficult to handle. In addressing the need for a reliable solution, a method based on an electrochemically active adhesive was developed. In this method, an electrochemically active adhesive was diluted and spin coated on a 100 mm diameter silicon wafer (carrier wafer) on which another silicon wafer (device wafer) was bonded. Device wafer was subjected to post processing fabrication technique such as wafer thinning. Successful debonding of the device wafer was achieved by applying a voltage between the two wafers. In another part of the research, a fabrication process for developing a functional nanoporous material using atomic layer deposition is presented. In order to realize a nanoporous electrode, a nanoporous anodized aluminum oxide (AAO) substrate was used, which was functionalized with very thin layers (~ 10 nm) of platinum (Pt) and aluminum oxide (Al2O3) using atomic layer deposition. Nanoporous material when used as an electrode delivers high sensitivity due to the inherent high surface area and is potentially applicable in fuel cells and in electrochemical sensing.

The second part of the thesis addresses the need for a high performance gas sensor that is applicable for asthma monitoring. Asthma is a disease related to the inflammation in the airways of the lungs and is characterized by the presence of nitric oxide gas in the exhaled breath. The gas concentration of above approximately 50 parts-per-billion indicates a likely presence of asthma. A MEMS based electrochemical gas sensor was successfully designed and developed to meet the stringent requirements needed for asthma detection. Furthermore, to enable a hand held asthma measuring instrument, a miniaturized sensor with integrated electrodes and liquid electrolyte was developed. The electrodes were assembled at a wafer-level to demonstrate the feasibility towards a high volume fabrication of the gas sensors. In addition, the designed amperometric gas sensor was successfully tested for hydrogen sulphide concentration, which is a bio marker for bad breath.

Place, publisher, year, edition, pages
Stockholm: KTH Royal Institute of Technology, 2015. xiv, 77 p.
TRITA-EE, ISSN 1653-5146 ; 2015:030
MEMS, gas sensors, electrochemical, nitric oxide, hydrogen sulphide, nafion, nano
National Category
Engineering and Technology
urn:nbn:se:kth:diva-172955 (URN)978-91-7595-661-9 (ISBN)
Public defence
2015-10-02, Q2, Osquldas väg 10,, Stockholm, 10:00 (English)
EU, European Research Council, 267528VINNOVASwedish Research Council

QC 20150907

Available from: 2015-09-07 Created: 2015-09-03 Last updated: 2015-09-07Bibliographically approved

Open Access in DiVA

No full text

Other links

Publisher's full textScopus

Search in DiVA

By author/editor
Gatty, Hithesh K.Leijonmarck, SimonAntelius, MikaelStemme, GöranRoxhed, Niclas
By organisation
Micro and NanosystemsApplied Electrochemistry
In the same journal
Sensors and actuators. B, Chemical
Chemical SciencesMedical Laboratory and Measurements Technologies

Search outside of DiVA

GoogleGoogle Scholar
The number of downloads is the sum of all downloads of full texts. It may include eg previous versions that are now no longer available

Altmetric score

Total: 270 hits
ReferencesLink to record
Permanent link

Direct link