Change search
ReferencesLink to record
Permanent link

Direct link
Size and shape characterization of fines and fillers: a review
KTH, School of Industrial Engineering and Management (ITM), Production Engineering, Metrology and Optics. Innventia AB, SE-11428 Stockholm, Sweden.ORCID iD: 0000-0002-1467-7413
2015 (English)In: Nordic Pulp & Paper Research Journal, ISSN 0283-2631, E-ISSN 2000-0669, Vol. 30, no 3, 466-487 p.Article in journal (Refereed) Published
Abstract [en]

Many properties of fines and fillers are dependent on their size and shape. This review is on the literature on size and shape characterization of fines and fillers. It takes into account measurement techniques of particle width, length, equivalent diameter, area, and shape/morphology. The advantages and limitations of different methods are discussed. Measurement of other particles properties, e.g., optical, chemical or rheological, were not included in the review. Size and shape characterization methods can be roughly divided into gravimetric and non-gravimetric methods. Gravimetric measurements methods account for all particles in the sample, but give only indicative size and shape information. Non-gravimetric methods usually give more direct size and shape information, but only account for particles larger than the resolution of the instrument. Additionally, measuring both larger and smaller particles simultaneously is rarely possible. An implication is that current analysers fail to measure a larger share of the sample, for example fibrils, which have a high impact on product properties. Of the reviewed measurement techniques, flow microscopy had the highest potential. Based on instruments found in other application areas, possible developments for flow microscopes include multiwavelength illumination and sensors, fluorescent staining, and hydrodynamic focusing.

Place, publisher, year, edition, pages
2015. Vol. 30, no 3, 466-487 p.
National Category
Paper, Pulp and Fiber Technology
URN: urn:nbn:se:kth:diva-175521ISI: 000361615500012ScopusID: 2-s2.0-84951767329OAI: diva2:862014
Swedish Energy Agency

QC 20151020

Available from: 2015-10-20 Created: 2015-10-16 Last updated: 2016-01-22Bibliographically approved
In thesis
1. Image-based quantitative infrared analysis and microparticle characterisation for pulp and paper applications
Open this publication in new window or tab >>Image-based quantitative infrared analysis and microparticle characterisation for pulp and paper applications
2016 (English)Doctoral thesis, comprehensive summary (Other academic)
Abstract [en]

Measurements of process variations and particle morphology are widely employed in the pulp and paper industry. Two techniques with high potential, infrared thermography and microparticle characterisation, are mainly used qualitatively. Quantitative thermography requires knowledge of the emittance, a material property which has not been measured under many process-relevant conditions. Quantitative characterisation of microparticles, e.g. pulp fines and mineral fillers, requires the analysis of a large number of particles, which can be accomplished using flow microscopes. Flow microscopes for pulp analysis have had insufficient spatial resolution to resolve fines and fillers. Additionally, there has been a lack of methods which can differentiate between fines and fillers in a mixed suspension.

State-of-the-art instruments for particle image analysis were evaluated and compared to laser diffractometry, a measurement method based on scattering by diffraction. Laser diffractometry was found to be highly sensitive to the complex refractive index of the particles, and especially to its change due to moisture absorption. A high-resolution imaging flow cytometer and a high-resolution fibre analyser were found to be complementary for characterisation of pure fines and fines/filler mixtures, and superior to laser diffractometry. A method for differentiating between fines and fillers in a suspension based on their autofluorescence and side-scattering was proposed and qualitatively evaluated.

Furthermore, a method for measuring the directional and integrated emittance of paper was developed and its accuracy was determined. Measurements on a wide range of samples showed that the emittance of fibre-based materials vary significantly with wavelength, pulp type, observation angle, and moisture content. By applying measured quantitative values of the emittance, the thermal energy emitted by sack paper samples during mechanical deformation could be quantitatively calculated. The increase in thermal energy at the time of rupture was found to correlate well with the elastic share of the mechanical energy that was stored in the sample during its elongation.

In summary, the results of this work have facilitated the use of quantitative microparticle analysis and infrared thermography for pulp and paper applications. 

Abstract [sv]

Mätningar av processvariationer och partiklars form och storlek utförs i stor skala inom massa- och pappersindustrin. Två mättekniker med stor potential, infraröd termografi och mikropartikel-karaktärisering, används mest kvalitativt idag. Kvantitativ termografi kräver att provets emittans är känd. Emittansen är en materialegenskap som inte har mätts för många förhållanden som är relevanta inom papperstillverkning. Kvantitativ karaktärisering av partiklar kräver att ett tillräckligt stort antal partiklar analyseras, något som kan göras med flödesmikroskop. Flödesmikroskop för mäldanalys har haft otillräcklig upplösning för att karaktärisera mikrometerstora partiklar, t.ex. fines och fyllmedel. Det har heller inte funnits någon metod som kan särskilja mellan fines och fyllmedel i en blandning.

Högupplösta mätinstrument för bildbaserad mikropartikelkaraktärisering utvärderades och jämfördes med en laserdiffraktometer, en mätmetod baserad på ljusspridning genom diffraktion. Laserdiffraktometerns mätresultat påverkades starkt av det brytningsindex som antogs för provet, och hur brytningsindexet ändrades med fukthalt. En högupplöst bildbaserad flödescytometer och en högupplöst fibermätare konstaterades komplettera varandra vid mätningar av mäldens finmaterial. De var även pålitligare än laserdiffraktometern vid mätningar av organiskt finmaterial. En metod för att skilja mellan organiskt och oorganiskt finmaterial i en mäld baserat på deras autofluorescens och ljusspridning presenterades och utvärderades kvalitativt.

En metod för att mäta den vinkelberoende och våglängdsintegrerade emittansen hos fiberbaserade material utvecklades och dess mätnoggrannhet utvärderades. Mätningar på ett stort antal prover visade att emittansen varierade betydligt med våglängd, mäldtyp, observationsvinkel, och fukthalt. Genom att använda den uppmätta emittansen kunde den termiska energin som frigjordes av ett säckpappersprov vid brottögonblicket beräknas. Denna energi korrelerade väl med den elastiska energi som lagrades i provet medan det töjdes, fram till tidpunkten för brottet.

Sammanfattningsvis har resultaten av detta arbete möjliggjort kvantitativ användning av mikropartikel-karaktärisering och infraröd termografi i massa- och papperstillämpningar.

Place, publisher, year, edition, pages
Stockholm: KTH Royal Institute of Technology, 2016. 132 p.
TRITA-IIP, ISSN 1650-1888 ; 16:01
Metrology, stock, papermaking, refining, fibrillation, fines, filler, morphology, classification, flow microscopy, fibre analyser, flow cytometry, laser diffraction, dynamic image analysis, process variation, thermography, emittance, emissivity, infrared, MWIR, LWIR, goniometer
National Category
Reliability and Maintenance Paper, Pulp and Fiber Technology
Research subject
Production Engineering; Fibre and Polymer Science
urn:nbn:se:kth:diva-180722 (URN)978-91-7595-843-9 (ISBN)
Public defence
2016-02-12, Innoversum, Innventia, Drottning Kristinas Väg 61, Solna, 10:00 (English)
Swedish Energy AgencyÖnnesjö Foundation

QC 20160122

Available from: 2016-01-22 Created: 2016-01-21 Last updated: 2016-01-22Bibliographically approved

Open Access in DiVA

The full text will be freely available from 2016-11-30 13:16
Available from 2016-11-30 13:16


Search in DiVA

By author/editor
Hyll, Kari
By organisation
Metrology and Optics
In the same journal
Nordic Pulp & Paper Research Journal
Paper, Pulp and Fiber Technology

Search outside of DiVA

GoogleGoogle Scholar
The number of downloads is the sum of all downloads of full texts. It may include eg previous versions that are now no longer available

Total: 295 hits
ReferencesLink to record
Permanent link

Direct link