Change search
ReferencesLink to record
Permanent link

Direct link
Surface integrity of 2304 duplex stainless steel after different grinding operations
KTH, School of Chemical Science and Engineering (CHE), Chemistry, Surface and Corrosion Science. Department of Material Science, Dalarna University, Sweden.
KTH, School of Chemical Science and Engineering (CHE), Chemistry, Surface and Corrosion Science. Jernkontoret, SE-11187 Stockholm, Sweden.
2016 (English)In: Journal of Materials Processing Technology, ISSN 0924-0136, E-ISSN 1873-4774, Vol. 229, 294-304 p.Article in journal (Refereed) PublishedText
Abstract [en]

Surface integrity has significant effect on service performance of a component. In this study, the evolution of the surface and sub-surface changes induced by grinding duplex stainless steel (DSS) 2304 was studied with regard to the residual stress, the microstructure, surface roughness and surface defects. The results provide insights into the effect of abrasive grit size, grinding force and lubrication on the surface integrity. The abrasive grit size was found to have the largest influence. Surface defects, a highly deformed surface layer and the generation of tensile residual stresses along the grinding direction have been found to be the main types of damage induced by the grinding operation. Residual stresses induced by mechanical effects dominate over thermal effects in this study. The results obtained can be used to understand the contribution of surface condition and residual stress on failure of duplex stainless steels in service by fatigue or stress corrosion cracking.

Place, publisher, year, edition, pages
Elsevier, 2016. Vol. 229, 294-304 p.
Keyword [en]
Surface integrity, Grinding, Duplex stainless steel 2304, Residual stress
National Category
Chemical Sciences
Identifiers
URN: urn:nbn:se:kth:diva-180580DOI: 10.1016/j.jmatprotec.2015.09.031ISI: 000367106000029ScopusID: 2-s2.0-84942475434OAI: oai:DiVA.org:kth-180580DiVA: diva2:896616
Note

QC 20160126

Available from: 2016-01-21 Created: 2016-01-19 Last updated: 2016-02-03Bibliographically approved
In thesis
1. Influence of grinding operations on surface integrity and chloride induced stress corrosion cracking of stainless steels
Open this publication in new window or tab >>Influence of grinding operations on surface integrity and chloride induced stress corrosion cracking of stainless steels
2016 (English)Licentiate thesis, comprehensive summary (Other academic)
Abstract [en]

Stainless steels were developed in the early 20th century and are used where both the mechanical properties of steels and corrosion resistance are required. There is continuous research to allow stainless steel components to be produced in a more economical way and be used in more harsh environments. A necessary component in this effort is to correlate the service performance with the production processes.

The central theme of this thesis is the mechanical grinding process.  This is commonly used for producing stainless steel components, and results in varied surface properties that will strongly affect their service life. The influence of grinding parameters including abrasive grit size, machine power and grinding lubricant were studied for 304L austenitic stainless steel (Paper II) and 2304 duplex stainless steel (Paper I). Surface integrity was proved to vary significantly with different grinding parameters. Abrasive grit size was found to have the largest influence. Surface defects (deep grooves, smearing, adhesive/cold welding chips and indentations), a highly deformed surface layer up to a few microns in thickness and the generation of high level tensile residual stresses in the surface layer along the grinding direction were observed as the main types of damage when grinding stainless steels. A large degree of residual stress anisotropy is interpreted as being due to mechanical effects dominating over thermal effects.

The effect of grinding on stress corrosion cracking behaviour of 304L austenitic stainless steel in a chloride environment was also investigated (Paper III). Depending on the surface conditions, the actual loading by four-point bend was found to deviate from the calculated value using the formula according to ASTM G39 by different amounts. Grinding-induced surface tensile residual stress was suggested as the main factor to cause micro-cracks initiation on the ground surfaces. Grinding along the loading direction was proved to increase the susceptibility to chloride-induced SCC, while grinding perpendicular to the loading direction improved SCC resistance.

The knowledge obtained from this work can provide a reference for choosing appropriate grinding parameters when fabricating stainless steel components; and can also be used to help understanding the failure mechanism of ground stainless steel components during service.

Place, publisher, year, edition, pages
Stockholm: KTH Royal Institute of Technology, 2016. 72 p.
Series
TRITA-CHE-Report, ISSN 1654-1081 ; 2016:5
National Category
Corrosion Engineering
Research subject
Chemistry
Identifiers
urn:nbn:se:kth:diva-180817 (URN)978-91-7595-838-5 (ISBN)
Presentation
2016-02-25, Sal Q34, Osqualdas väg 6, KTH, Stockholm, 13:00 (English)
Opponent
Supervisors
Note

QC 20160203

Available from: 2016-02-03 Created: 2016-01-23 Last updated: 2016-02-03Bibliographically approved

Open Access in DiVA

No full text

Other links

Publisher's full textScopus

Search in DiVA

By author/editor
Zhou, NianPettersson, Rachel
By organisation
Surface and Corrosion Science
In the same journal
Journal of Materials Processing Technology
Chemical Sciences

Search outside of DiVA

GoogleGoogle Scholar
The number of downloads is the sum of all downloads of full texts. It may include eg previous versions that are now no longer available

Altmetric score

Total: 41 hits
ReferencesLink to record
Permanent link

Direct link