The main objective of this thesis work was to gain understanding of the layer properties and polymer structures that were able to aid lubrication in aqueous media. To this end, three types of polyelectrolytes: a diblock copolymer, a train-of-brushes and two brush-with-anchor mucins have been utilized. Their lubrication ability in the boundary lubrication regime has been examined by Atomic Force Microscopy with colloidal probe.
The interfacial behavior of the thermoresponsive diblock copolymer, PIPOZ60-b-PAMPTAM17,on silica was studied in the temperature interval 25-50 ˚C. The main finding is that adsorption hysteresis, due to the presence of trapped states, is important when the adsorbed layers are in contact with a dilute polymer solution. The importance of trapped states was also demonstrated in the measured friction forces, where significantly lower friction forces, at a given temperature, were encountered on cooling than on the preceding heating stage, which was attributed to increased adsorbed amount. On the heating stage the friction force decreased with increasing temperature despite the worsening of the solvent condition, and the opposite trend was observed when using pre-adsorbed layers (constant adsorbed amount) as a consequence of increased segment-segment attraction.
The second part of the studies was devoted to the interfacial properties of mucins on PMMA. The strong affinity provided by the anchoring group of C-PSLex and C-P55 together with their more extended layer structure contribute to the superior lubrication of PMMA compared to BSM up to pressures of 8-9 MPa. This is a result of minor bridging and lateral motion of molecules along the surface during shearing. We further studied the influence of glycosylation on interfacial properties of mucin by utilizing the highly purified mucins, C-P55 and C-PSLex. Our data suggest that the longer and more branched carbohydrate side chains on C-PSLex provide lower interpenetration and better hydration lubrication at low loads compared to the shorter carbohydrate chains on C-P55. However, the longer carbohydrates appear to counteract disentanglement less efficiently, giving rise to a higher friction force at high loads.
Two series of mononuclear ruthenium complexes [Ru(pdc)L-3] (H(2)pdc = 2,6-pyridinedicarboxylic acid; L = 4-methoxypyridine, 1; pyridine, 2; pyrazine, 3) and [Ru(pdc)L-2(dmso)] (dmso = dimethyl sulfoxide; L = 4-methoxypyridine, 4; pyridine, 5) were synthesized and spectroscopically characterized. Their catalytic activity toward water oxidation has been examined using Ce-IV (Ce(NH4)(2)(NO3)(6)) as the chemical oxidant under acidic conditions. Complexes 1, 2 and 3 are capable of catalyzing Ce-IV-driven water oxidation while 4 and 5 are not active. Electronic effects on their catalytic activity were illustrated: electron donating groups increase the catalytic activity.
A nonionic-cationic diblock copolymer, poly(2-isopropyl-2-oxazoline)(60)-b-poly((3-acrylamidopropyl)- trimethylammonium chloride)(17), (PIPOZ(60)-b-PAMPTMA(17)), was utilized to electrostatically tether temperature-responsive PIPOZ chains to silica surfaces by physisorption. The effects of polymer concentration, pH, and temperature on adsorption were investigated using quartz crystal microbalance with dissipation monitoring and ellipsometry. The combination of these two techniques allows thorough characterization of the adsorbed layer in terms of surface excess, thickness, and water content. The high affinity of the cationic PAMPTMA(17) block to the negatively charged silica surface gives rise to a high affinity adsorption isotherm, leading to (nearly) irreversible adsorption with respect to dilution. An increase in solution pH lowers the affinity of PIPOZ to silica but enhances the adsorption of the cationic block due to increasing silica surface charge density, which leads to higher adsorption of the cationic diblock copolymer. Higher surface excess is also achieved at higher temperatures due to the worsening of the solvent quality of water for the PIPOZ block. Interestingly, a large hysteresis in adsorbed mass and other layer properties was observed when the temperature was cycled from 25 to 45 degrees C and then back to 25 degrees C. Possible causes for this temperature hysteresis are discussed.
Interfacial properties of two types of mucins have been investigated at the aqueous solution/poly(methyl methacrylate) (PMMA) interface. One is commercially available bovine submaxillary mucin, BSM, which consists of alternating glycosylated and nonglycosylated regions. The other one is a recombinant mucin-type fusion protein, PSGL-1/mIgG(2b), consisting of a glycosylated mucin part fused to the Fc part of an immunoglobulin. PSGL-1/mIgG(2b) is mainly expressed as a (timer upon production. A quartz crystal microbalance with dissipation was used to study the adsorption of the mucins to PMMA surfaces. The mass of the adsorbed mucin layers, including the adsorbed mucin and water trapped in the layer, was found to be significantly higher for PSGL-1/mIgG(2b) than for BSM. Atomic force microscopy with colloidal probe was employed to study interactions and frictional forces between mucin-coated PMMA surfaces. Purely repulsive forces of steric origin were Observed between PSGL-1/mIgG(2b) mucin layers, whereas a small adhesion was detected between BSM layers and attributed to bridging. Both mucin layers reduced the friction force between PMMA surfaces in aqueous solution. The reduction was, however, significantly more pronounced for PSGL-1/mIgG(2b). The effective friction coefficient between PSGL-1/mIgG(2b)-coated PMMA surfaces is as low as 0.02 at low loads, increasing to 0.24 at the highest load explored, 50 nN. In contrast, a friction coefficient of around 0.7 was obtained between BSM-coated PMMA surfaces. The large differences in interfacial properties for the two mucins are discussed in relation to their structural differences.
Interfacial properties of two brush-with-anchor mucins, C-P55 and C-PSLex, have been investigated at the aqueous solution/poly(methyl methacrylate) (PMMA) interface. Both are recombinant mucin-type fusion proteins, produced by fusing the glycosylated mucin part of P-selectin glycoprotein ligand-1 (PSLG-1) to the Fc part of a mouse immunoglobulin in two different cells. They are mainly expressed as dimers upon production. Analysis of the O-glycans shows that the C-PSLex mucin has the longer and more branched side chains, but C-P55 has slightly higher sialic acid content. The adsorption of the mucins to PMMA surfaces was studied by quartz crystal microbalance with dissipation. The sensed mass, including the adsorbed mucin and water trapped in the layer, was found to be similar for these two mucin layers. Atomic force microscopy with colloidal probe was employed to study surface and friction forces between mucin-coated PMMA surfaces. Purely repulsive forces of steric origin were observed between mucin layers on compression, whereas a small adhesion was detected between both mucin layers on decompression. This was attributed to chain entanglement. The friction force between C-PSLex-coated PMMA is lower than that between C-P55-coated PMMA. at low loads, but vice versa at high loads. We discuss our results in terms of the differences in the glycosylation composition of these two mucins.
Interfacial properties of two brush-with-anchor mucins, C-P55 and C-PSLex, have been investigated at the aqueous solution/poly(methylmethacrylate) (PMMA) interface. Both are recombinant mucin-type fusion proteins, produced by fusing the glycosylated mucin part of P-selectin glycoprotein ligand-1 (PSLG-1) to the Fc part of a mouse immunoglobulin in two different cells. They are mainly expressed as dimers upon production. Analysis of the O-glycans shows that the C-PSLex mucin has the longer and more branched side chains, but C-P55 has slightly higher sialic acid content. The adsorption of the mucins to PMMA surfaces was studied by quartz crystal microbalance with dissipation. The sensed mass, including the adsorbed mucin and water trapped in the layer, was found to be similar for these two mucin layers. Atomic force microscopy with colloidal probe was employed to study surface and friction forces between mucin-coated PMMA surfaces. Purely repulsive forces of steric origin were observed between mucin layers on compression, whereas a small adhesion was detected between both mucin layers on decompression. This was attributed to chain entanglement. The friction force between C-PSLex-coated PMMA is lower than that between C-P55-coated PMMA at low loads, but vice versa at high loads. We discuss our results in terms of the differences in the glycosylation composition of these two mucins.
Equilibration in adsorbing polymer systems can be very slow, leading to different physical properties at a given condition depending on the pathway that was used to reach this state. Here we explore this phenomenon using a diblock copolymer consisting of a cationic anchor block and a thermoresponsive block of poly(2-isopropyl-2-oxazoline), PIPOZ. We find that at a given temperature different polymer chain densities at the silica surface are achieved depending on the previous temperature history. We explore how this affects surface and friction forces between such layers using the atomic force microscope colloidal probe technique. The surface forces are purely repulsive at temperatures <40 degrees C. A local force minimum at short separation develops at 40 degrees C and a strong attraction due to capillary condensation of a polymer-rich phase is observed close to the bulk phase separation temperature. The friction forces decrease in the cooling stage due to rehydration of the PIPOZ chain. A consequence of the adsorption hysteresis is that the friction forces measured at 25 degrees C are significantly lower after exposure to a temperature of 40 degrees C than prior to heating, which is due to higher polymer chain density on the surface after heating.
Thermoresponsive polymer layers on silica surfaces have been obtained by utilizing electrostatically driven adsorption of a cationic-nonionic diblock copolymer. The cationic block provides strong anchoring to the surface for the nonionic block of poly(2-isopropyl-2-oxazoline), referred to as PIPOZ. The PIPOZ chain interacts favorably with water at low temperatures, but above 46 degrees C aqueous solutions of PIPOZ phase separate as water becomes a poor solvent for the polymer. We explore how a change in solvent condition affects interactions between such adsorbed layers and report temperature effects on both normal forces and friction forces. To gain further insight, we utilize self-consistent lattice mean-field theory to follow how changes in temperature affect the polymer segment density distributions and to calculate surface force curves. We find that with worsening of the solvent condition an attraction develops between the adsorbed PIPOZ layers, and this observation is in good agreement with predictions of the mean-field theory. The modeling also demonstrates that the segment density profile and the degree of chain interpenetration under a given load between two PIPOZ-coated surfaces rise significantly with increasing temperature.
Hyaluronan has been found to play an important role in boundary lubrication in joints, but model experiments have shown that free hyaluronan is reluctant to stay between surfaces. We show that hyaluronan, when assisted by a phospholipid bilayer, can act as a boundary lubricant, even at pressures well above those leading to breakdown of cartilage.
Phospholipids and hyaluronan have been implied to fulfil important roles in synovial joint lubrication. Since both components are present in synovial fluid, self-assembly structures formed by them should also be present. We demonstrate by small angle X-ray scattering that hyaluronan associates with the outer shell of dipalmitoylphophatidylcholine (DPPC) vesicles in bulk solution. Further, we follow adsorption to silica from mixed hyaluronan/DPPC vesicle solution by Quartz Crystal Microbalance with Dissipation measurements. Atomic Force Microscope imaging visualises the adsorbed layer structure consisting of non-homogeneous phospholipid bilayer with hyaluronan/DPPC aggregates on top. The presence of these aggregates generates a long-range repulsive surface force as two such surfaces are brought together. However, the aggregates are easily deformed, partly rearranged into multilayer structures and partly removed from between the surfaces under high loads. These layers offer very low friction coefficient (<0.01), high load bearing capacity (approximate to 23 MPa), and self-healing ability. Surface bound DPPC/hyaluronan aggregates provide a means for accumulation of lubricating DPPC molecules on sliding surfaces.
The interactions between silica nanoparticles grafted with a brush of cationic poly(2-(dimethylamino) ethyl methacrylate) (SiO2-g-PDMAEMA) and anionic surfactant sodium dodecyl sulfate (SDS) is investigated by dynamic light scattering, electrophoretic mobility, quartz crystal microbalance with dissipation, ellipsometry, and atomic force microscopy. SiO2-g-PDMAEMA exhibits pH-dependent charge and size properties which enable the SDS binding to be probed over a range of electrostatic conditions and brush conformations. SDS monomers bind irreversibly to SiO2-g-PDMAEMA at low surfactant concentrations (similar to 10(-4) M) while exhibiting a pH-dependent threshold above which cooperative, partially reversible SDS binding occurs. At pH 5, SDS binding induces collapse of the highly charged and swollen brush as observed in the bulk by DLS and on surfaces by QCM-D. Similar experiments at pH 9 suggest that SDS binds to the periphery of the weakly charged and deswollen brush and produces SiO2-g-PDMAEMA/SDS complexes with a net negative charge. SiO2-g-PDMAEMA brush collapse and charge neutralization is further confirmed by colloidal probe AFM measurements, where reduced electrosteric repulsions and bridging adhesion are attributed to effects of the bound SDS. Additionally, sequential adsorption schemes with SDS and SiO2-g-PDMAEMA are used to enhance deposition relative to SiO2-g-PDMAEMA direct adsorption on silica. This work shows that the polyelectrolyte brush configuration responds in a more dramatic fashion to SDS than to pH-induced changes in ionization, and this can be exploited to manipulate the structure of adsorbed layers and the corresponding forces of compression and friction between opposing surfaces.
Hyaluronan and phospholipids play an important role in lubrication in articular joints and provide in combination with glycoproteins exceptionally low friction coefficients. We have investigated the structural organization of 1,2-dipalmitoyl-sn-glycero-3-phosphocholine (DPPC) Langmuir layers at the solution-air interface at different length scales with respect to the adsorption of hyaluronan (HA). This allows us to assemble a comprehensive picture of the adsorption and the resulting structures, and how they are affected by the molecular weight of HA and the presence of calcium ions. Brewster angle microscopy and grazing incident diffraction were used to determine the lateral structure at the micro- and macro scale. The data reveals an influence of HA on both the macro and micro structure of the DPPC Langmuir layer, and that the strength of this effect increases with decreasing molecular weight of HA and in presence of calcium ions. Furthermore, from X-ray reflectivity measurements we conclude that HA adsorbs to the hydrophilic part of DPPC, but data also suggest that two types of interfacial structures are formed at the interface. We argue that hydrophobic forces and electrostatic interactions play important rules for the association between DPPC and HA. Surface pressure area isotherms were used to determine the influence of HA on the phase behavior of DPPC while electrophoretic mobility measurements were used to gain insight into the binding of calcium ions to DPPC vesicles and hyaluronan.