kth.sePublications KTH
Planned maintenance
A system upgrade is planned for 17/11-2026, at 12:00-14:00. During this time DiVA will be unavailable.
Change search
Link to record
Permanent link

Direct link
Publications (10 of 18) Show all publications
Scarano, E., Arvidsson, E., Roos, A. K., Holmgren, E., Borgani, R., Tholén, M. O. & Haviland, D. B. (2025). Low-temperature AFM with a microwave cavity optomechanical transducer. Beilstein Journal of Nanotechnology, 16, 1873-1882
Open this publication in new window or tab >>Low-temperature AFM with a microwave cavity optomechanical transducer
Show others...
2025 (English)In: Beilstein Journal of Nanotechnology, ISSN 2190-4286, Vol. 16, p. 1873-1882Article in journal (Refereed) Published
Abstract [en]

We demonstrate atomic force microscopy (AFM) imaging with a microcantilever force transducer where an integrated superconducting microwave resonant circuit detects cantilever deflection using the principles of cavity optomechanics. We discuss the detector responsivity and added noise, pointing to its crucial role in the context of force sensitivity. Through analysis of noise measurements we determine the effective temperature of the cantilever eigenmode and we determine the region of detector operation in which the sensor is thermal-noise-limited. Our analysis shows that the force-sensor design is a significant improvement over piezoelectric force sensors commonly used in low-temperature AFM. We discuss the potential for further improvement of the sensor design to achieve optimal detection at the standard quantum limit. We demonstrate AFM operation with surface-tracking feedback in both amplitude-modulation and frequency-modulation modes.

Place, publisher, year, edition, pages
Beilstein Institut, 2025
Keywords
atomic force microscopy, cavity optomechanics
National Category
Atom and Molecular Physics and Optics Other Physics Topics Condensed Matter Physics
Identifiers
urn:nbn:se:kth:diva-372572 (URN)10.3762/bjnano.16.130 (DOI)001602940900001 ()41158734 (PubMedID)2-s2.0-105019757958 (Scopus ID)
Note

QC 20251110

Available from: 2025-11-10 Created: 2025-11-10 Last updated: 2025-11-10Bibliographically approved
Roos, A. K., Scarano, E., Arvidsson, E., Holmgren, E. & Haviland, D. B. (2024). Design, fabrication, and characterization of kinetic-inductive force sensors for scanning probe applications. , 15
Open this publication in new window or tab >>Design, fabrication, and characterization of kinetic-inductive force sensors for scanning probe applications
Show others...
2024 (English)Manuscript (preprint) (Other academic)
Abstract [en]

We describe a transducer for low-temperature atomic force microscopy based on electromechanical coupling due to a strain-dependent kinetic inductance of a superconducting nanowire. The force sensor is a bending triangular plate (cantilever) whose deflection is measured via a shift in the resonant frequency of a high-Q superconducting microwave resonator at 4.5 GHz. We present design simulations including mechanical finite-element modeling of surface strain and electromagnetic simulations of meandering nanowires with large kinetic inductance. We discuss a lumped-element model of the force sensor and describe the role of an additional shunt inductance for tuning the coupling to the transmission line used to measure the microwave resonance. A detailed description of our fabrication is presented, including information about the process parameters used for each layer. We also discuss the fabrication of sharp tips on the cantilever using focused electron beam-induced deposition of platinum. Finally, we present measurements that characterize the spread of mechanical resonant frequency, the temperature dependence of the microwave resonance, and the sensor's operation as an electromechanical transducer of force. 

Keywords
force sensing, atomic force microscopy, kinetic inductance, superconductivity, optomechanics
National Category
Nano Technology
Research subject
Physics, Material and Nano Physics
Identifiers
urn:nbn:se:kth:diva-343023 (URN)10.48550/arXiv.2310.03569 (DOI)
Funder
EU, Horizon 2020, 828966Swedish Foundation for Strategic Research, ITM17-0343
Note

QC 20240208

Available from: 2024-02-05 Created: 2024-02-05 Last updated: 2024-02-20Bibliographically approved
Roos, A. K., Scarano, E., Arvidsson, E., Holmgren, E. & Haviland, D. B. (2024). Design, fabrication, and characterization of kinetic-inductive force sensors for scanning probe applications. Beilstein Journal of Nanotechnology, 15, 242-255
Open this publication in new window or tab >>Design, fabrication, and characterization of kinetic-inductive force sensors for scanning probe applications
Show others...
2024 (English)In: Beilstein Journal of Nanotechnology, E-ISSN 2190-4286, Vol. 15, p. 242-255Article in journal (Refereed) Published
Abstract [en]

We describe a transducer for low-temperature atomic force microscopy based on electromechanical coupling due to a strain-dependent kinetic inductance of a superconducting nanowire. The force sensor is a bending triangular plate (cantilever) whose deflection is measured via a shift in the resonant frequency of a high-Q superconducting microwave resonator at 4.5 GHz. We present design simulations including mechanical finite-element modeling of surface strain and electromagnetic simulations of meandering nanowires with large kinetic inductance. We discuss a lumped-element model of the force sensor and describe the role of an additional shunt inductance for tuning the coupling to the transmission line used to measure the microwave resonance. A detailed description of our fabrication is presented, including information about the process parameters used for each layer. We also discuss the fabrication of sharp tips on the cantilever using focused electron beam-induced deposition of platinum. Finally, we present measurements that characterize the spread of mechanical resonant frequency, the temperature dependence of the microwave resonance, and the sensor’s operation as an electromechanical transducer of force.

Place, publisher, year, edition, pages
Frankfurt am Main, Germany: Beilstein Institut, 2024
Keywords
atomic force microscopy, force sensing, kinetic inductance, optomechanics, superconductivity
National Category
Nano Technology
Identifiers
urn:nbn:se:kth:diva-343570 (URN)10.3762/bjnano.15.23 (DOI)001162781300001 ()2-s2.0-85191661029 (Scopus ID)
Note

QC 20240301

Available from: 2024-02-20 Created: 2024-02-20 Last updated: 2024-11-18Bibliographically approved
Scarano, E., Arvidsson, E., Roos, A. K., Holmgren, E. & Haviland, D. B. (2024). Intrinsic Kerr amplification for microwave electromechanics. Applied Physics Letters, 124, Article ID 243503.
Open this publication in new window or tab >>Intrinsic Kerr amplification for microwave electromechanics
Show others...
2024 (English)In: Applied Physics Letters, ISSN 0003-6951, E-ISSN 1077-3118, Vol. 124, article id 243503Article in journal (Refereed) Published
Abstract [en]

Electromechanical transduction gain of 21 dB is realized in a micro-cantilever resonant force sensor operated in the unresolved-sideband regime. Strain-dependent kinetic inductance weakly couples cantilever motion to a superconducting nonlinear resonant circuit. A single pump generates motional sidebands and parametrically amplifies them via four-wave mixing. We study the gain and added noise, and we analyze potential benefits of this integrated amplification process in the context force sensitivity.

Place, publisher, year, edition, pages
American Institute of Physics (AIP), 2024
Keywords
kerr nonlinearity, microwave resonators, superconductivity, kinetic inductance, four-wave mixing, parametric amplification
National Category
Nano Technology
Research subject
Physics, Material and Nano Physics
Identifiers
urn:nbn:se:kth:diva-343027 (URN)10.1063/5.0201936 (DOI)001248285000007 ()2-s2.0-85196043756 (Scopus ID)
Funder
EU, Horizon 2020, 828966Swedish Foundation for Strategic Research, ITM17-0343
Note

QC 20240702

Available from: 2024-02-05 Created: 2024-02-05 Last updated: 2024-11-18Bibliographically approved
Scarano, E., Arvidsson, E., Roos, A. K., Holmgren, E. & Haviland, D. B. (2024). Temperature dependence of microwave losses in lumped-element resonators made from superconducting nanowires with high kinetic inductance. Superconductor Science and Technology, 37(7), Article ID 075013.
Open this publication in new window or tab >>Temperature dependence of microwave losses in lumped-element resonators made from superconducting nanowires with high kinetic inductance
Show others...
2024 (English)In: Superconductor Science and Technology, ISSN 1361-6668, Vol. 37, no 7, article id 075013Article in journal (Refereed) Published
Abstract [en]

We study the response of several microwave resonators made from superconducting NbTiN thin-film meandering nanowires with large kinetic inductance, having different circuit topology and coupling to the transmission line. Reflection measurements reveal the parameters of the circuit and analysis of their temperature dependence in the range 1.7-6 K extract the superconducting energy gap and critical temperature. The lumped-element LC resonator, valid in our frequency range of interest, allows us to predict the quasiparticle contribution to internal loss, independent of circuit topology and characteristic impedance. Our analysis shows that the internal quality factor is limited not by thermal-equilibrium quasiparticles, but an additional temperature-dependent source of internal microwave loss. 

Place, publisher, year, edition, pages
Institute of Physics (IOP), 2024
Keywords
kinetic inductance, superconductivity, microwave resonators, mattis-bardeen
National Category
Nano Technology
Research subject
Physics, Material and Nano Physics
Identifiers
urn:nbn:se:kth:diva-343024 (URN)10.1088/1361-6668/ad4d5c (DOI)001248945600001 ()2-s2.0-85196036472 (Scopus ID)
Funder
EU, Horizon 2020, 828966Swedish Foundation for Strategic Research, ITM17-0343
Note

QC 20240702

Available from: 2024-02-05 Created: 2024-02-05 Last updated: 2024-11-18Bibliographically approved
Roos, A. K., Scarano, E., Arvidsson, E. K., Holmgren, E. & Haviland, D. B. (2023). Kinetic Inductive Electromechanical Transduction for Nanoscale Force Sensing. Physical Review Applied, 20(2), Article ID 024022.
Open this publication in new window or tab >>Kinetic Inductive Electromechanical Transduction for Nanoscale Force Sensing
Show others...
2023 (English)In: Physical Review Applied, E-ISSN 2331-7019, Vol. 20, no 2, article id 024022Article in journal (Refereed) Published
Abstract [en]

We use the principles of cavity optomechanics to design a resonant mechanical force sensor for atomic force microscopy. The sensor is based on a type of electromechanical coupling, dual to traditional capacitive coupling, whereby the motion of a cantilever induces surface strain that causes a change in the kinetic inductance of a superconducting nanowire. The cavity is realized by a compact microwave-plasma mode with an equivalent LC circuit involving the kinetic inductance of the nanowire. The device is fully coplanar and we show how to transform the cavity impedance for optimal coupling to the transmission line and the following amplifier. For the device presented here, we estimate the bare kinetic inductive mechanoelectric coupling (KIMEC) rate g0/2π in the range 3–10 Hz. We demonstrate phase-sensitive detection of cantilever motion using a multifrequency pumping and measurement scheme.

Place, publisher, year, edition, pages
American Physical Society, 2023
National Category
Nano Technology
Research subject
Physics
Identifiers
urn:nbn:se:kth:diva-334375 (URN)10.1103/physrevapplied.20.024022 (DOI)001052945100003 ()2-s2.0-85168731329 (Scopus ID)
Funder
Swedish Foundation for Strategic Research, ITM17-0343EU, Horizon 2020, 828966
Note

QC 20230825

Available from: 2023-08-18 Created: 2023-08-18 Last updated: 2024-11-18Bibliographically approved
Polishchuk, D., Kulyk, M., Holmgren, E., Pasquale, G., Kravets, A. F. & Korenivski, V. (2020). Influence of nanosize effect and non-magnetic dilution on interlayer exchange coupling in fe–cr/cr nanostructures. Ukrainian Journal of Physics, 65(10), 892-897
Open this publication in new window or tab >>Influence of nanosize effect and non-magnetic dilution on interlayer exchange coupling in fe–cr/cr nanostructures
Show others...
2020 (English)In: Ukrainian Journal of Physics, ISSN 2071-0186, Vol. 65, no 10, p. 892-897Article in journal (Refereed) Published
Abstract [en]

Magnetic properties of multilayered [Fe–Cr/Cr] ×8 nanostruc-tures with the interlayer exchange coupling of the antiferro-magnetic type and without the interlayer coupling have been studied. The values of the saturation magnetization and the interlayer exchange coupling constant are shown to strongly depend on the thickness and non-magnetic dilution of the Fe– Cr layers. It is found that those parameters differently affect the interlayer exchange coupling, which is explained by an interplay between the size effect (the thickness of the Fe–Cr lay-ers) and the magnetic polarization of the Fe–Cr/Cr interfaces depending on the Fe concentration.

Place, publisher, year, edition, pages
National Academy of Sciences of Ukraine, 2020
National Category
Condensed Matter Physics
Identifiers
urn:nbn:se:kth:diva-288006 (URN)10.15407/ujpe65.10.898 (DOI)000581771300008 ()2-s2.0-85092666216 (Scopus ID)
Note

QC 20201229

Available from: 2020-12-29 Created: 2020-12-29 Last updated: 2023-08-28Bibliographically approved
Polishchuk, D., Persson, M., Kulyk, M., Holmgren, E., Pasquale, G. & Korenivski, V. (2020). Tuning thermo-magnetic properties of dilute-ferromagnet multilayers using RKKY interaction. Applied Physics Letters, 117(2), Article ID 022402.
Open this publication in new window or tab >>Tuning thermo-magnetic properties of dilute-ferromagnet multilayers using RKKY interaction
Show others...
2020 (English)In: Applied Physics Letters, ISSN 0003-6951, E-ISSN 1077-3118, Vol. 117, no 2, article id 022402Article in journal (Refereed) Published
Abstract [en]

We demonstrate a 20-fold enhancement in the strength of the Ruderman-Kittel-Kasuya-Yosida interlayer exchange in dilute-ferromagnet/normal-metal multilayers by incorporating ultrathin Fe layers at the interfaces. Additionally, the resulting increase in the interface magnetic polarization profoundly affects the finite-size effects, sharpening the Curie transition of the multilayer, while allowing us to separately tune its Curie temperature via intra-layer magnetic dilution. These results should be useful for designing functional materials for applications in magnetocaloric micro-refrigeration and thermally assisted spin-electronics.

Place, publisher, year, edition, pages
AIP Publishing, 2020
National Category
Condensed Matter Physics
Identifiers
urn:nbn:se:kth:diva-279169 (URN)10.1063/5.0014823 (DOI)000553127000002 ()2-s2.0-85088466253 (Scopus ID)
Note

QC 20200909

Available from: 2020-09-09 Created: 2020-09-09 Last updated: 2023-12-05Bibliographically approved
Bondarenko, A., Holmgren, E., Li, Z. W., Ivanov, B. A. & Korenivski, V. (2019). Chaotic dynamics in spin-vortex pairs. Physical Review B, 99, Article ID 054402.
Open this publication in new window or tab >>Chaotic dynamics in spin-vortex pairs
Show others...
2019 (English)In: Physical Review B, ISSN 2469-9950, E-ISSN 2469-9969, Vol. 99, article id 054402Article in journal (Refereed) Published
Abstract [en]

We report on spin-vortex pair dynamics measured at temperatures low enough to suppress stochastic core motion, thereby uncovering the highly nonlinear intrinsic dynamics of the system. Our analysis shows that the decoupling of the two vortex cores is resonant and can be enhanced by dynamic chaos. We detail the regions of the relevant parameter space, in which the various mechanisms of the resonant core-core dynamics are activated. We show that the presence of chaos can reduce the thermally induced spread in the decoupling time by up to two orders of magnitude.

National Category
Condensed Matter Physics
Identifiers
urn:nbn:se:kth:diva-248013 (URN)10.1103/PhysRevB.99.054402 (DOI)000457728700004 ()2-s2.0-85061380893 (Scopus ID)
Funder
Swedish Research Council, 2014-4546Swedish Research Council, 2018-03526
Note

QC 20190402

Available from: 2019-04-02 Created: 2019-04-02 Last updated: 2023-08-28Bibliographically approved
Holmgren, E., Persson, M. & Korenivski, V. (2019). Effects of asymmetry in strongly coupled spin vortex pairs. Journal of Physics D: Applied Physics, 52(10), Article ID 105001.
Open this publication in new window or tab >>Effects of asymmetry in strongly coupled spin vortex pairs
2019 (English)In: Journal of Physics D: Applied Physics, ISSN 0022-3727, E-ISSN 1361-6463, Vol. 52, no 10, article id 105001Article in journal (Refereed) Published
Abstract [en]

Effects of magnetic asymmetry on strongly coupled spin-vortex pairs with parallel core polarization and antiparallel chirality in synthetic nanomagnets are investigated. This includes vortex-core length asymmetry, biasing field asymmetry, and pinning of one of the two vortex cores. Our experimental observations as well as analytical and micromagnetic modeling show how magnetic asymmetry can be used to differentiate magneto-resistively otherwise degenerate multiple stable states of a vortex pair. These results expand the knowledge base for spin vortex arrays in nanostructures and should be useful in light of the recent proposals on coding information into multiple topological spin states, such as single and multiple vortex core/chirality states.

Place, publisher, year, edition, pages
IOP PUBLISHING LTD, 2019
Keywords
vortex core pinning, magnetic vortex memory, magnetic vortex pairs
National Category
Condensed Matter Physics
Identifiers
urn:nbn:se:kth:diva-241298 (URN)10.1088/1361-6463/aaf8f7 (DOI)000455128200001 ()2-s2.0-85060232971 (Scopus ID)
Note

QC 20190222

Available from: 2019-02-22 Created: 2019-02-22 Last updated: 2023-08-28Bibliographically approved
Organisations
Identifiers
ORCID iD: ORCID iD iconorcid.org/0000-0003-1543-6838

Search in DiVA

Show all publications