This work demonstrates a versatile and environmentally friendly route for the development of new orthogonal monomers that can be used for postfunctionalizable polymer networks. A monomer containing both vinyl ether (VE) and cyclic disulfide moieties was synthesized via enzyme catalysis under benign reaction conditions. The bifunctional monomer could be polymerized to form macromolecues with differing architectures by the use of either cationic or radical photo polymerization. When cationic polymerization was performed, a linear polymer was obtained with pendant disulfide units in the side chain, whereas in the presence of radical initiator, the VE reacted with the disulfide to yield a branched structure. The monomer was thereafter used to design networks that could be postfunctionalized; the monomer was cross-linked with cationic initiation together with a difunctional VE oligomer and after cross-linking the unreacted disulfides were coupled to RhodamineVE by radical UV-initiation.

The performance of different esterification catalysts was studied for the use in synthesis of renewable polyesters from dimethyl itaconate (DMI), dimethyl succinate (DMS) and 1,4-butanediol (BD). Itaconic acid and derivatives such as DMI are interesting monomers because of their multiple functionalities and previous work has shown great potential. However, the multiple functionalities also pose challenges to avoid side reactions such as thermally initiated, premature, radical crosslinking and/or isomerization of the 1,1-disubstituted unsaturation. Additionally, the two carboxylic acids have inherently different reactivity. One key factor to control reactions with IA is to understand the performance of different catalysts. In this study, six esterification catalysts were investigated; immobilized Candida antarctica lipase B (CalB), titanium(IV)butoxide (Ti(OBu)4), p-toluenesulfonic acid (pTSA), sulfuric acid (H2SO4), 1,8-diazabicycloundec-7-ene (DBU), and 1,5,7-triazabicyclodec-5-ene (TBD). CalB and Ti(OBu)4 were selected for further characterization with appreciable differences in catalytic activity and selectivity towards DMI. CalB was the most effective catalysts and was applied at 60 °C while Ti(OBu)4 required 160 °C for a reasonable reaction rate. CalB was selective towards DMS and the non-conjugated side of DMI, resulting in polyesters with itaconate-residues mainly located at the chain ends, while Ti(OBu)4 showed low selectivity, resulting in polyesters with more randomly incorporated itaconate units. Thermal analysis of the polyesters showed that the CalB-catalyzed polyesters were semi-crystalline, whereas the Ti(OBu)4-catalyzed polyesters were amorphous, affirming the difference in monomer sequence. The polyester resins were crosslinked by UV-initiated free radical polymerization and the material properties were evaluated and showed that the crosslinked materials had similar material properties. The films from the polyester resins catalyzed by CalB were furthermore completely free from discoloration whereas the film made from the polyester resins catalyzed with Ti(OBu)4 had a yellow color, caused by the catalyst. Thus, it has been shown that CalB can be used to attain sustainable unsaturated polyesters resins for coating applications, exhibiting equally good properties as resins obtained from traditional metal-catalysis.

Increased environmental awareness has led to a demand for sustainable, bio-based materials. Consequently, the development of new benign synthesis pathways utilizing a minimum of reaction steps and available bio-based building blocks is needed. In the present study, vinyl ether alcohols and functional carboxylic acids were used to synthesize bifunctional vinyl ether esters using the immobilized enzyme Candida antarctica lipase B as a catalyst. Vinyl ethers are attractive alternatives to (meth)acrylates due to low allergenic hazards, low toxicity, and fast polymerization; however, difficult synthesis limits the monomer availability. The synthesis was performed in one-pot and the described method was successful within a broad temperature range (22-90 degrees C) and in various organic solvents as well as in the bulk. The synthesis of different vinyl ether esters reached high conversions (above 90%) after less than 1 h and products were purified by removing the enzyme by filtration using only small amounts of acetone. This approach is a straightforward route to reach monomers with multiple types of functionalities that can be used as different photo-curable thermoset resins. In this work, this was demonstrated by polymerizing the monomers with cationic and radical UV-polymerization. By changing the functional carboxylic acids, the architecture of the final polymer can be tailored, herein demonstrated by two examples. In the developed versatile method, carboxylic acids can be used directly as acyl donors, constituting a more sustainable alternative to the carboxylic acid derivatives used today.

There is a demand for new sustainable polymeric materials. Vinyl ethers are, in this context, attractive oligomers since they polymerize fast, are non-toxic, and can be polymerized under ambient conditions. The availability of vinyl ether oligomers is, however, currently limited due to difficulties in synthesizing them without using tedious synthesis routes. This work presents the synthesis of a series of vinyl ether ester oligomers using enzyme catalysis under solvent-free conditions and the subsequent photoinduced cationic polymerization to form polymer thermosets with T(g)s ranging from -10 to 100 degrees C. The whole process is very efficient as the synthesis takes less than 1 h with no need for purification and the crosslinking is complete within 2 min.

A series of renewable unsaturated polyesters were synthesized from itaconic acid (IA), succinic acid, and 1,4-butanediol by solvent-free polycondensation. Previous studies utilizing IA to make polyesters for coating applications have shown great potential; however, the curing and material properties have not been investigated in detail. The aim of this study was to investigate how the curing is affected by the amount of unsaturations and how well itaconate-based polyesters crosslink without the addition of any other unsaturated monomers or reactive diluents. The chemical structures of the polyesters were confirmed with FTIR, 1 HNMR, and THF-SEC. The degree of curing was studied with FTIR, and the mechanical properties of the crosslinked polyesters were evaluated with DMA, pendulum hardness, and microindentation. The degree of curing was found to be up to 75%, and furthermore, it was found that the final mechanical properties of the crosslinked coatings could be tuned by modifying the IA content in the monomer composition. The results from DMA showed that there is a clear trend between mechanical properties and crosslinking density.