Series capacitors are installed in transmission lines to increase power transfer capacity. However, their addition creates challenges for the line protection. Security and speed of phasor based protection schemes that work with local measurements (communication independent) are severely affected in the presence of series capacitors. Therefore, time-domain based protection methods may be considered as a potential solution for communication independent protection of series compensated lines. In this paper, an incremental quantity based protection scheme is presented for series compensated lines with the capacitor in the middle of the line. The method involves estimating the voltage across the capacitor bank, based on the current in the capacitor bank and metal oxide varistor during faults. Then this capacitor voltage estimation is used to implement the incremental quantity protection. The incremental quantity method consists of fault detection, phase selection, directional discrimination and distance estimation. A PSCAD model of a 500 kV, 200 km transmission line is used to simulate fault cases for evaluating the method. The proposed method is tested with different compensation levels, fault types, fault positions, inception angles, fault resistances and source impedance ratios. The results show that the proposed method can meet the dependability and security demands for the protection of series compensated lines.

Series capacitors increase the power transfer limit of transmission lines. However, the protection of series compensated lines using only local measurement is challenging. Phasor based distance protection experiences delay and directional problems in the presence of a series capacitor. This paper presents an incremental quantity based distance protection algorithm for series compensated lines. The algorithm uses instantaneous voltage and current measurement from the local bus. It consists of capacitor voltage estimation, fault detection, phase selection, directional discrimination and distance estimation. The algorithm is extensively tested based on simulations with a line-end series capacitor, considering different source impedance ratios, fault inception angle, compensation levels, and fault resistance, location and type. This time-domain method is shown to work well, with fast decision time.

Introduction of series capacitors in transmission lines can cause problems with reliability and security of distance protection, due to problems such as current inversion, voltage inversion and sub-synchronous oscillation. Distance protection is widely used for transmission lines and has desirable features not available from traditional alternatives, which has motivated attempts to adapt it to work better with series capacitors. Research and development in overcoming the challenges using distance protection in series compensated lines have also been actively pursued during this period. Thus there is a need to summarize and systematically categorize developments, to show recent trends and highlight further research opportunities. This paper aims to fill that gap by a thorough literature survey of distance protection of series compensated lines, including a clear background of the problems that need to be solved. The scope of this work is limited to distance protection schemes that work with local measurements only. It is observed that the developments in this domain are largely concentrated on voltage drop estimation across capacitor bank, phasor estimation and adaptive protection schemes. This work will provide an overview of the latest developments for experienced researchers and will be a reference for new researchers interested in this domain.

Series compensation of transmission lines creates several challenges for distance protection, particularly at the high compensation levels that have recently become more common. In this paper, the effect of high levels of series compensation on distance protection is evaluated, using a PSCAD simulation model of a 500 kV, 200 km transmission line with a series capacitor bank. The capacitor bank model includes overvoltage protection using a metal oxide varistor (MOV) and bypass circuit breaker. Compensation levels of 70%, 100% and 140% are simulated and phase to ground faults are simulated at several positions along the line, with fault resistance of 0 Ω and 30 Ω and fault inception angle of 0 ° and 90 °. It is observed from the simulation results that traditional distance protection experiences severe challenges at high levels of series compensation. With increasing compensation level, an increased length of line experiences voltage inversion and current inversion during a fault. The fault trajectories in the R-X plane show that voltage and current inversion during a fault can cause directional problems and delay for the distance relay. Sub-synchronous oscillation (SSO) is observed for faults in series compensated lines, causing over-reach and under-reach problems as well as delayed relay operation.

Series capacitors are used in some transmission lines to raise the power transfer limit. If a fault occurs at a location behind which the total reactance is capacitive, the result is current inversion, also known as current reversal. In a current inversion, current leads the voltage instead of lagging it. The probability of current inversion increases with higher levels of compensation. In this paper, the effect of current inversion is studied in distance and differential protection of transmission lines. A 500 kV transmission line is modelled, with compensation levels of 70%, 100% and 140%. Phase to ground faults are applied with fault inception angles of 0, 60 and 90. It is shown that current inversion can cause serious problems with distance protection. Differential protection is not severely affected by current inversion. The protection schemes are significantly influenced by parameters of the capacitor bank overvoltage protection components, particularly the metal-oxide varistor.

Travelling-wave and time-domain-based protection functions provide significant response time improvements over conventional phasor-based protection functions in power systems. These types of protection functions require very high sampling rates in the order of several hundreds of kHz. This paper proposes a novel centralized substation protection architecture (CPC) based on distributed signal processing units (DSPU) that enables the deployment of these high sampling rate applications in digital substations utilizing an Ethernet-based process-level network. The design of the DSPU is elaborated, and its signal processing algorithms are discussed. Moreover, the performance of the DSPU is analysed through dynamic tests and verified through a numerical electromaanetic transient simulation.

Series capacitors create challenges for traditional phasor-based distance relays in power transmission lines. Phasor based distance relays experience directional problems and delays.This paper compares the performance of phasor-based distance protection in series compensated line protection with three other distance protection methods. The first method is based on incremental quantities in the time domain, the second is based on Lissajous curves and conic section general equation, and the third is based on the RL and RLC model of the transmission line.The performance of these methods is evaluated in different fault conditions that create problems for phasor-based distance protection.Their relative advantages and disadvantages are outlined and discussed to identify their suitability for series compensated line protection. It is observed that the incremental quantity and model-based protections give fast and secure protection in series compensated lines. The conic section general equation based method can help avoid inversion, but the operating speed is slower than the other methods.

We demonstrate a time-domain estimation of impedance, based on the conic-section general equation and Lissajous curves, applied to protection of transmission lines that have series-capacitor compensation. This method helps to avoid the problems experienced by phasor-based distance relays when series compensation leads to voltage inversion or current inversion. Validation is performed using data from simulations of series compensated lines with a wide range of parameters such as sampling frequency, source impedance ratio, compensation level, fault inception angle,fault resistance, and fault location. It is seen that this method works well for series compensated lines, with operating times in the range of one and a half cycles.

Fast time-domain distance protection using RL and RLC models of a transmission line is presented in this paper for application to series compensated transmission lines. The proposed method is suited to both line-terminal andmid-line series compensation. It avoids classic limitations of delays and directional problems that phasor-based distance protection exhibits in series compensated transmission lines in the presence of voltage or current inversion sand subsynchronous oscillations. The method is validated with different system parameters such as compensation levels, source impedance ratio, fault inception angle, and fault resistance. The proposed method works well, with operating times in the range of a half cycle.