kth.sePublikationer KTH
Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Improving energy-efficiency of electric vehicles by over-actuation
KTH, Skolan för teknikvetenskap (SCI), Teknisk mekanik, Farkostteknik och Solidmekanik, Fordonsdynamik.ORCID-id: 0000-0002-2592-917X
2020 (Engelska)Doktorsavhandling, sammanläggning (Övrigt vetenskapligt)
Abstract [en]

As the concerns regarding environmental pollution, climate change and the fossilfuel crisis have grown, electric vehicles (EVs) have attracted a great deal of attention. However, for EVs to be more competitive compared with internal combustion engine vehicles (ICEVs), their driving range needs to be increased. Therefore,energy-efficient control of EVs is considered to be a very important research field.

Electrification of actuators for EVs makes decentralized driving systems possible,such as systems providing individual wheel torque, individual wheel steering andindividual wheel camber control. Electrified vehicle actuators can provide morecontrol possibilities than the normal control of motion in the longitudinal and thelateral direction. EVs equipped with these kinds of actuators are thereby overactuated and more advanced motion controls focusing on energy-efficiency andvehicle directional stability can be realised.

The research objective of the work presented in this doctoral thesis was the exploration of energy-efficient control methods for over-actuated EVs. In order toevaluate the contribution of different control strategies to energy saving, modelsfor energy loss during driving, especially during cornering, were developed. Both alinear tyre model with a camber effect and a non-linear tyre model with a cambereffect were studied. The powertrain efficiency based on a motor efficiency map ofin-wheel motors, was considered.

On the basis of vehicle dynamics with a linear tyre model, camber’s contributionto tyre slip loss reduction during cornering and the corresponding contributionof direct yaw moment control (DYC) when neglecting the powertrain losses werestudied and compared. The results show that camber control can reduce the tyreslip loss significantly and DYC in this case has a small contribution to tyre slip lossreduction. Using a non-linear tyre model, a camber controller based on the lateralacceleration was developed, the effectiveness of this controller was evaluated andthe results show a promising energy saving.

In addition, to investigate the influence of the powertrain losses, a DYC for energyefficiency considering a motor efficiency map was proposed. While satisfying thesame cornering demand, by actively distributing the wheel torques using DYC forenergy-efficiency, the overall energy-efficiency during non-safety-critical manoeuvres could be improved.

Since there might be a higher risk of accidents when applying DYC for energyefficiency in safety-critical manoeuvres, a DYC for safety was developed based ona stability judgement considering the yaw rate and slip angle. To handle this compromise, a switching principle for alternating between DYC for energy-efficiencyand DYC for stability was then proposed. Furthermore, a method for designing arule-based DYC for energy-efficiency was developed to reduce the calculation task and thereby enable real-time implementation.

This research has resulted in an increased understanding of how to improve energyefficiency using different actuators in an over-actuated EV. Different ways in whichover-actuation of EVs can improve the energy-efficiency are presented and analysed in this thesis. Altogether, potential energy loss reductions (up to 22% usingcamber control) for the studied vehicles and manoeuvres have been found usingthe developed methods. Even though the actual improvement will depend on theconsidered vehicle, actuators and driving conditions, the methodology presented inthis thesis can be applied to other vehicles and driving situations.

Ort, förlag, år, upplaga, sidor
Stockholm: KTH Royal Institute of Technology, 2020. , s. ix, 64
Serie
TRITA-SCI-FOU ; 2020:09
Nationell ämneskategori
Farkost och rymdteknik
Forskningsämne
Farkostteknik
Identifikatorer
URN: urn:nbn:se:kth:diva-272045ISBN: 978-91-7873-494-8 (tryckt)OAI: oai:DiVA.org:kth-272045DiVA, id: diva2:1423806
Disputation
2020-05-08, Live-streaming: https://kth-se.zoom.us/j/69854468785, Stockholm, 09:00 (Engelska)
Opponent
Handledare
Anmärkning

QC 20200416

Tillgänglig från: 2020-04-16 Skapad: 2020-04-15 Senast uppdaterad: 2025-03-17Bibliografiskt granskad
Delarbeten
1. Exploring the potential of camber control to improve vehicles' energy efficiency during cornering
Öppna denna publikation i ny flik eller fönster >>Exploring the potential of camber control to improve vehicles' energy efficiency during cornering
Visa övriga...
2018 (Engelska)Ingår i: Energies, E-ISSN 1996-1073, Vol. 11, nr 4, artikel-id 724Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

Actively controlling the camber angle to improve energy efficiency has recently gained interest due to the importance of reducing energy consumption and the driveline electrification trend that makes cost-efficient implementation of actuators possible. To analyse how much energy that can be saved with camber control, the effect of changing the camber angles on the forces and moments of the tyre under different driving conditions should be considered. In this paper, Magic Formula tyre models for combined slip and camber are used for simulation of energy analysis. The components of power loss during cornering are formulated and used to explain the influence that camber angles have on the power loss. For the studied driving paths and the assumed driver model, the simulation results show that active camber control can have considerable influence on power loss during cornering. Different combinations of camber angles are simulated, and a camber control algorithm is proposed and verified in simulation. The results show that the camber controller has very promising application prospects for energy-efficient cornering.

Ort, förlag, år, upplaga, sidor
MDPI AG, 2018
Nyckelord
Camber, Cornering, Energy saving, Magic formula
Nationell ämneskategori
Energisystem
Identifikatorer
urn:nbn:se:kth:diva-227632 (URN)10.3390/en11040724 (DOI)000434703400035 ()2-s2.0-85044506343 (Scopus ID)
Anmärkning

QC 20180515

Tillgänglig från: 2018-05-15 Skapad: 2018-05-15 Senast uppdaterad: 2024-03-15Bibliografiskt granskad
2. Analysis of camber control and torque vectoring to improve vehicle energy efficiency
Öppna denna publikation i ny flik eller fönster >>Analysis of camber control and torque vectoring to improve vehicle energy efficiency
Visa övriga...
2018 (Engelska)Ingår i: The Dynamics of Vehicles on Roads and Tracks, CRC Press/Balkema , 2018, s. 121-128Konferensbidrag, Publicerat paper (Refereegranskat)
Abstract [en]

This paper focuses on the use of camber control and torque vectoring in order to make future vehicles more energy efficient and thereby more environmentally friendly. The energy loss during steady state cornering including rolling resistance loss, aerodynamic loss, longitudinal slip loss and lateral slip loss, is formulated and studied. Camber control, torque vectoring control and a combination of both are compared. From the simulation results, it can be concluded that during steady state cornering, torque vectoring has a very small contribution to energy reduction while camber control can make a significant contribution to energy saving. By combining torque vectoring and camber control during steady state cornering, in theory up to 14% energy saving are found for certain cases.

Ort, förlag, år, upplaga, sidor
CRC Press/Balkema, 2018
Nyckelord
Camber control, Energy saving, Steady state cornering, Torque vectoring, Cambers, Energy conservation, Energy dissipation, Torque, Aerodynamic loss, Energy efficient, Energy reduction, Steady state, Energy efficiency
Nationell ämneskategori
Farkost och rymdteknik
Identifikatorer
urn:nbn:se:kth:diva-247414 (URN)000469105100019 ()2-s2.0-85061316493 (Scopus ID)9781138035713 (ISBN)
Konferens
25th Symposium of the International Association of Vehicle System Dynamics, IAVSD 2017, 14 August 2017 through 18 August 2017
Anmärkning

QC20190502

Tillgänglig från: 2019-05-02 Skapad: 2019-05-02 Senast uppdaterad: 2025-02-14Bibliografiskt granskad
3. Energy-Efficient Direct Yaw Moment Control for In-Wheel Motor Electric Vehicles Utilising Motor Efficiency Maps
Öppna denna publikation i ny flik eller fönster >>Energy-Efficient Direct Yaw Moment Control for In-Wheel Motor Electric Vehicles Utilising Motor Efficiency Maps
2020 (Engelska)Ingår i: Energies, E-ISSN 1996-1073, Vol. 13, nr 3, artikel-id 593Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

An active energy-efficient direct yaw moment control (DYC) for in-wheel motor electric vehicles taking motor efficiency maps into consideration is proposed in this paper. The potential contribution of DYC to energy saving during quasi-steady-state cornering is analysed. The study in this paper has produced promising results which show that DYC can be used to reduce the power consumption while satisfying the same cornering demand. A controller structure that includes a driver model and an offline torque distribution law during continuous driving and cornering is developed. For comparison, the power consumption of stability DYC is also analysed. Simulations for double lane change manoeuvres are performed and driving conditions either with a constant velocity or with longitudinal acceleration are designed to verify the effectiveness of the proposed controller in different driving situations. Under constant velocity cornering, since the total torque demand is not high, two rear wheels are engaged and during cornering it is beneficial to distribute more torque to one wheel to improve energy efficiency. In the simulated driving manoeuvres, up to 10% energy can be saved compared to other control methods. During acceleration in cornering, since the total torque demand is high, it is energy-efficient to use all the four in-wheel motors during cornering.

Ort, förlag, år, upplaga, sidor
MDPI, 2020
Nyckelord
electric vehicles, energy efficiency, direct yaw moment control, motor efficiency map, in-wheel motor technology
Nationell ämneskategori
Farkost och rymdteknik
Identifikatorer
urn:nbn:se:kth:diva-272755 (URN)10.3390/en13030593 (DOI)000522489000086 ()2-s2.0-85079007546 (Scopus ID)
Anmärkning

QC 20200526

Tillgänglig från: 2020-05-26 Skapad: 2020-05-26 Senast uppdaterad: 2025-03-14Bibliografiskt granskad

Open Access i DiVA

fulltext(6270 kB)1378 nedladdningar
Filinformation
Filnamn FULLTEXT01.pdfFilstorlek 6270 kBChecksumma SHA-512
3db2e30db0f39734151843669672a6c5bccf58629ba0243671f9333ebf0ae1d6f6e1e8dceeabbc94888dca6f936eb6db2c26e394a9766f69fd7a9591d298582a
Typ fulltextMimetyp application/pdf

Person

Sun, Peikun

Sök vidare i DiVA

Av författaren/redaktören
Sun, Peikun
Av organisationen
Fordonsdynamik
Farkost och rymdteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar
Totalt: 1382 nedladdningar
Antalet nedladdningar är summan av nedladdningar för alla fulltexter. Det kan inkludera t.ex tidigare versioner som nu inte längre är tillgängliga.

isbn
urn-nbn

Altmetricpoäng

isbn
urn-nbn
Totalt: 1125 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf