Crystal Plasticity-Based Analysis of Mechanical Response and Strain-Induced α’-Martensite Evolution in Fe-Cr-Ni Austenitic Steels
2026 (English)Independent thesis Advanced level (degree of Master (Two Years)), 20 credits / 30 HE credits
Student thesis
Abstract [en]
Metastable Fe-Cr-Ni austenitic steels can show complex deformation behaviour because dislocation slip, mechanical twinning and deformation-induced martensitic transformation may operate simultaneously. In this thesis, a crystal plasticity-based model is utilized to study coupled TWIP/TRIP response and predict the evolution of strain-induced α’-martensite during tensile deformation based on the γ→ϵ→α’ transformation pathway.
Synthetic three-dimensional microstructures were generated based on EBSD-derived grain size and orientation information. The grain size distributions were first fitted using a lognormal distribution, and the fitted parameters were used as direct input for generating synthetic polycrystals. The generated microstructures were then used for Crystal Plasticity Fast Fourier transform (CPFFT) simulations with a TWIP/TRIP model. The constitutive parameters were calibrated manually in a stepwise manner against in situ tensile HEXRD experiments. The calibration was performed for two austenitic stainless steel alloys with different stacking fault energies and five grain size distributions.
The CP model was used to statistically estimate the nucleation kinetics and resultant volume fraction of twins and ϵ-martensite based on the resolved shear stress on 111<110> slip and 111<112> twin systems. Subsequently, a statistical surrogate model based on shear-band intersections was used to estimate α’-martensite nucleation kinetics from the simulated twin and ϵ-martensite volume fractions. The predicted martensite evolution was compared with experimental in situ tensile HEXRD data.
The calibrated CP model was able to predict the effect of grain size on twin and ϵ-martensite nucleation kinetics consistent with the original TWIP/TRIP model. Twins were predicted to nucleate mainly in coarse grains and the twin fraction increased with grain size. Meanwhile, ϵ-martensite nucleated preferably near fine grain clusters and the volume fraction decreased with increasing grain size. The surrogate model was also able to correctly predict the relation between grain size and α’-martensite nucleation kinetics compared to in situ HEXRD. Hence, the CP model along with the surrogate model can be useful to study the effect of grain size on martensite formation in Austenitic stainless steels.
Abstract [sv]
Metastabila Fe-Cr-Ni-austenitiska stål kan uppvisa ett komplext deformationsbeteende eftersom dislokationsglidning, mekanisk tvillingbildning och deformationsinducerad martensitisk transformation kan verka samtidigt. I detta examensarbete används en kristallplasticitetsbaserad modell för att studera den kopplade TWIP/TRIP-responsen och förutsäga utvecklingen av töjningsinducerad α’-martensit under drag-deformation, baserat på transformationsvägen γ →ϵ→α’.
Syntetiska tredimensionella mikrostrukturer genererades baserat på EBSD-baserad information om kornstorlek och kristallografisk orientering. Kornstorleksfördelningarna anpassades först med hjälp av en lognormalfördelning, och de anpassade parametrarna användes som direkt indata för att generera syntetiska polykristaller. De genererade mikrostrukturerna användes därefter i simuleringar med Crystal Plasticity Fast Fourier Transform (CPFFT) med en TWIP/TRIP-modell. De konstitutiva parametrarna kalibrerades manuellt enligt ett stegvis förfarande mot in situ HEXRD-dragprovningsexperiment. Kalibreringen utfördes för två austenitiska rostfria stållegeringar med olika staplingsfelsenergier och fem kornstorleksfördelningar.
CP-modellen användes för att statistiskt uppskatta nukleationskinetiken och den resulterande volymfraktionen av tvillingar och ϵ-martensit, baserat på den upplösta skjuvspänningen på {111}<110>-glidsystem och {111}<112>-tvillingsystem. Därefter användes en statistisk surrogatmodell baserad på skjuvbandsintersektioner för att uppskatta nukleationskinetiken för α’-martensit från de simulerade volymfraktionerna av tvillingar och ϵ-martensit. Den förutsagda martensitutvecklingen jämfördes med experimentella in situ HEXRD-data från dragprovning.
Den kalibrerade CP-modellen kunde förutsäga effekten av kornstorlek på nukleationskinetiken för tvillingar och ϵ-martensit på ett sätt som överensstämmer med den ursprungliga TWIP/TRIP-modellen. Tvillingar förutsågs främst nukleera i grova korn, och tvillingfraktionen ökade med ökande kornstorlek. Samtidigt nukleerade ϵ-martensit företrädesvis i anslutning till finkorniga kornkluster, och volymfraktionen minskade med ökande kornstorlek. Surrogatmodellen kunde också korrekt förutsäga sambandet mellan kornstorlek och nukleationskinetik för α’-martensit jämfört med in situ HEXRD-resultaten. Därför kan CP-modellen tillsammans med surrogatmodellen vara användbar för att studera effekten av kornstorlek på martensitbildning i austenitiska rostfria stål.
Place, publisher, year, edition, pages
2026. , p. 44
Series
TRITA-ITM-EX ; 2026:608
Keywords [en]
Crystal Plasticity, TWIP, TRIP, Austenitic steel, Martensite nucleation
Keywords [sv]
Kristallplasticitet, TWIP, TRIP, austenitiskt stål, martensitnukleation
National Category
Engineering and Technology
Identifiers
URN: urn:nbn:se:kth:diva-391891OAI: oai:DiVA.org:kth-391891DiVA, id: diva2:2114831
Subject / course
Materials and Process Design
Educational program
Master of Science - Engineering Materials Science
Supervisors
Examiners
2026-11-032026-11-03